Ryobi RTMS1800 Traducción De Las Instrucciones Originales página 6

Ocultar thumbs Ver también para RTMS1800:
Tabla de contenido

Publicidad

the machine is still running and the head is not in the
rest position.
Never attempt to stop a machine in motion rapidly
by jamming a tool or other means against the blade,
serious accidents can be caused unintentionally in this
way.
Disconnect the saw from the mains supply before
changing blades or carrying out maintenance.
Pay attention to blade packing and unpacking, it is easy
to be injured by the sharp blade tips.
Use a blade holder or wear gloves when handling a saw
blade.
Keep and store the blade in original packaging or other
suitable packaging, keep in dry conditions and away
from chemicals which may damage the blade.
LASER SAFETY RULES
The laser radiation used in this saw is Class 2 with
into the laser beam. Failure to comply with the rules
could result in serious personal injury.
We have supplied you with an adhesive label in your
language and now request that you please apply this
over the top of the existing English language label
that is located on the side of the tool prior to first
commissioning the machine.
Do not stare into beam during operation.
Do not project the laser beam directly into the eyes of
others. Serious eye injury could result.
Do not place the laser in a position that may cause
anyone to stare into the laser beam intentionally or
unintentionally.
Do not use optical tools to view the laser beam.
Do not operate the laser around children or allow
children to operate the laser.
Do not attempt to repair the laser device by yourself.
Do not attempt to change any parts of the laser device
by yourself.
Any repairs must only be carried out by the laser
manufacturer or authorized service agent.
Do not replace the laser with a different type.
INTENDED USE
This machine is designed for ripping and cross
cutting operations on wood exclusively. It must be
fixed securely to a suitable height work bench, and is
intended to be operated by one person only.
In table saw mode, it is for through cuts only, no cutting
of slots or rebates. The maximum cutting capacity is
60mm.
In mitre saw mode, horizontal mitre angles of -45° to
+45° as well as vertical bevel angles of 0° to 45° are
possible. Maximum workpiece cross section 70mm x
4
| English
130mm.
The machine is designed to operate in one mode only,
it is not possible to use as a table saw and mitre saw
at the same time.
RESIDUAL RISKS
Even when the machine is used as prescribed, it is still
impossible to completely eliminate certain residual risk
factors. The following hazards may arise in use and the
operator should pay special attention to avoid the following:
Risk of contact with uncovered parts of the rotating saw
blade.
Kick-back of work pieces and parts of work pieces due
to improper adjustment or handling.
Catapulting of faulty carbide tips from the saw blade.
Damage to respiratory system if effective dust mask is
not worn.
Damage to hearing if effective hearing protection is not
worn.
MAINTENANCE
Do not make any adjustments while the motor is in
motion.
Always make sure the machine's plug has been
removed from the mains power source before changing
brushes, lubricating or when doing any works or
maintenance on the machine.
After each use, check your machine for damage or
broken parts and keep it in top working condition by
repairing or replacing parts immediately.
The blade being hot after use, keep the alertness
during maintenance or cleaning procedures.
Clean out accumulated dust.
To assure safety and reliability, all repairs with the
exception of externally accessible brushes should be
performed by an authorised service centre.
Faults in the machine, including guards or saw blades,
should be reported as soon as they are discovered.
If the power supply cord is damaged, it must be
replaced only by the manufacturer or by an authorized
service center to avoid risk. Contact authorized service
center.
ENVIRONMENTAL PROTECTION
Recycle raw materials instead of disposing
of as waste. The machine, accessories
and packaging should be sorted for
environmental-friendly recycling.
SYMBOL
Safety alert

Publicidad

Tabla de contenido
loading

Tabla de contenido