Publicidad
Idiomas disponibles
Idiomas disponibles
Connecting to the mains (adapter supplied):
• Only use the baby rocker with the recommended adapter.
• IMPORTANT: before any operation make sure your baby swing is switched off. The baby swing can function connected to a mains socket with
the aid of the adapter supplied. Input: 240 V / 60 Hz - Output: 6 V / 1000 mA
• Connect the adapter to the dedicated orifice and the other end in the mains socket.
• The adapters must be examined regularly so as to detect eventual damage to the lead, plug, case and other parts. Do not use the appliance if
you detect any damage.
a. Seat front part
b. Seat rotating arm
c. Cushion
d. Early learning mobile
Inclination of the back (3 positions)
Keep pressing on the two buttons on the sides of the back to select the position desired and then release. Make sure the inclination position is well
locked.
The seat can be rotated through 360° by holding the seat frame firmly and turning it to the position desired. A latch exists to block the baby rocker
in position.
Position the baby as in the image opposite. Slide the right and left parts of the harness belt until you hear a "click". Adjust the position of the belt
by sliding it along.
To detach the harness – press the central button in the harness.
WARNING! Be careful to adjust the safety belt for your child and block the 5 point safety harness well.
• The power button switches the baby rocker on and off.
• The buttons + and – (1) control the speed of the rocking. Press on + to increase the speed of the rocking and on – to decrease it. 4 rocking speeds
are available; a LED indicator light tells you which speed is activated.
• On/Off (2), this button starts the music and stops it.
• The Volume / Select (3) button lets you select the music as well as its volume. Press the button quickly to change the music. Press for a longer
time to adjust the volume.
• The Timer button (4) is for setting the timer. It is possible to program the rocking for 10, 20, or 30 minutes. A LED indicator shows whether the timer
is activated and for what time. By default the timer is not activated, no light should be on, and the rocking will continue until you stop it.
• When the locking mechanism is in the up position, the seat is blocked and cannot rock. If it is in the down position, rocking is possible.
• The movement detector button (5) enables the rocking to be start when the baby moves. You can activate this function by pressing the button (5);
an on/off light comes on when the movement detector is activated.
If the timer is not activated the rocking speed is immediately reset to level 0. If the baby wakes up the rocking starts again for 5 minutes.
If the timer is on, at the end of this period the rocking speed is reset to 0. The rocking will start again as soon as the baby wakes up for 5 minutes.
• Check the baby rocker frequently to make sure there are no loose screws, worn out parts, torn fabric, or unstitching.
• Have the parts replaced or repaired if necessary. Only use spare parts recommended by Babymoov.
• Clean the baby rocker regularly.
• The baby rocker headrest and cover are surface washable. This means they can be washed with a damp cloth and soap.
• To clean the frame of the baby rocker, use household soap or detergent and warm water exclusively. Do not use bleach.
• Heat or excessive exposure to the sun can cause the parts to fade or warp.
rn
j
100 % polyester
14
COMPOSITION OF THE BABY SWING
e. Front leg
f. Back leg
g. Motor
h. Seat back part
USE AND FEATURES OF THE BABY SWING
A. POSITIONS OF THE BABY SWING
B. ROTATION OF THE SEAT (B1 et B2)
C. FITTING THE HARNESS
D. MUSIC AND ROCKING
MAINTENANCE AND WASHING INSTRUCTIONS
360° MOTION BABY SWING • Instructions for use
WARNING
i. Seat side components
j. Morphological cushion
k. Adapter
Publicidad
