JL Audio FATHOM V2 Manual Del Propietário página 33

Built in USA with Imported and domestic components
Input Modes
F 12A H
250V
Grounded
Slave
120 V ~ 60 Hz
1200VA
Master Isolated
Output to Slave
(Balanced)
| Fathom v2
TROUBLESHOOTING - continued
D.A.R.O. Calibration attempt gives blinking Calibrate light
1. If the included JL Audio Microphone is not properly plugged into the front panel
jack, calibration will fail and the green Calibrate light will blink fast. Calibration
will ONLY proceed with the JL Audio microphone connected. Connecting any
other mic will cause the calibration to fail. Cancel the blinking Calibrate light by
pressing the Calibrate button again.
2. If calibration fails with the JL Audio microphone properly connected,
the green Calibrate light will blink slowly. Test the microphone and
cable connections and try running calibration again. If calibration
fails after following the steps above, the microphone or microphone
cable may be bad. Contact JL Audio Home Technical Support.
Your Fathom v2 is clearly audible outside of your house.
1. Revisit the "Master Level" setting on your Fathom v2(s) or your home theater
receiver/preamp/processor.
2. Inquire with your JL Audio dealer about noise isolation strategies.
3. Move the Fathom v2 away from windows.
MAIN FUSE HOLDER
Located on the rear panel, next to the AC cord receptacle is the main fuse holder's
cover. This small spring-loaded cap may be removed, allowing access to inspect
or replace the main power fuse. If your AC outlet has power but the Fathom v2's
lights do not come on, the main power fuse may be blown.
To Remove - Unplug the subwoofer's AC power cord. Insert a small flathead
INPUTS
screwdriver into the cap's slot and turn counter-clockwise slowly until the fuse holder
is released. Once removed, the fuse can be inspected and if necessary, replaced. Refer
LEFT
or
to the chart below for fuse values for your specific Fathom v2 model.
MONO
To Reinstall - Note that the fuse holder's body is keyed to the opening and must
Unbalanced
Balanced
be aligned to fit properly. Insert the fuse holder into the opening and gently turn
clockwise (about 1/8 turn) to lock in place. Pressing the cap and feeling for the spring
RIGHT
to compress will help to locate the correct position. Reconnect the AC power cord.
ONLY
If the replacement fuse blows immediately after a fuse replacement,
the subwoofer's amplifier may require service. Please contact your JL Audio
SERIAL NUMBER:
Authorized Retailer or Distributor.
Warranty void if serial number is removed, altered or defaced.
Fuse Ratings, 120V Models Only
Model
f110v2 (120V)
f112v2 (120V)
f113v2 (120V)
f212v2 (120V)
Fuse Ratings, 240V Models Only
Model
f110v2 (240V)
f112v2 (240V)
f113v2 (240V)
f212v2 (240V)
Fuse Type
0.25 x 1.25-inch, fast-acting
0.25 x 1.25-inch, fast-acting
0.25 x 1.25-inch, fast-acting
0.25 x 1.25-inch, fast-acting
Fuse Type
5mm x 20mm, fast-acting
5mm x 20mm, fast-acting
5mm x 20mm, fast-acting
5mm x 20mm, fast-acting
Fuse Size
7A, 250V
8A, 250V
12A, 250V
15A, 250V
Fuse Size
6.3A, 250V
6.3A, 250V
8A, 250V
10A, 250V
Page 33