Chamberlain MyQ CIGCWC Guía De Inicio Rápida página 3

FUNCTIONS
Push Bar (Open)
Learn LED
(Red)
LEARN
button
LOCK
button
1 Minute
TTC LED
5 Minute
TTC LED
10 Minute
TTC LED
PUSH BAR
Press the push bar to open/close the door.
LIGHTS
Press the LIGHT button to turn the garage door opener lights on or off.
When the lights are turned on they will stay on until the LIGHT button is
pressed again, or until the garage door opener is activated. Once the
garage door opener is activated the lights will turn off after the specified
period of time (the factory setting is 4-1/2 minutes). The LIGHT button
will not control the lights when the door is in motion.
To change the amount of time the garage door opener lights will stay on:
Press and hold the LOCK button until the garage door opener lights flash.
The time interval is indicated by the number of flashes.
NUMBER OF TIMES GARAGE
DOOR OPENER LIGHTS FLASH
TIME THE GARAGE DOOR
Minutes
OPENER LIGHT STAYS ON
Light Feature
The lights will turn on when someone enters through the open garage
door and the safety reversing sensor infrared beam is broken.
Activate:
Start with the garage door opener lights on. Press and hold the LIGHT
button until the garage door opener lights turn off, then on again.*
Deactivate:
Press and hold the LIGHT button until the garage door opener lights
turn on, then off again.*
* Approximately 10 seconds
MOTION SENSOR
This feature will automatically turn on the garage door opener lights when
motion is sensed. The lights will come on for the set period of time, then
shut off.
Activate/Deactivate:
Slide the motion sensor switch ON or OFF.
1 2 3
1 ½ 2 ½ 3 ½
Minutes Minutes
TIMER-TO-CLOSE (TTC)
DO NOT install this door control on garage door opener systems
NOTE:
controlling one-piece or swing doors.
The TTC feature automatically closes the door after a specified time
period (1, 5, or 10 minutes). Once the TTC has been set and the door is
Command
open, the LED for the selected close interval will blink and begin to count
LED (yellow)
down to close the door. The control panel will beep and the garage door
opener lights will flash before closing the door.
ON Button
The TTC feature will deactivate if the garage door encounters an
obstruction twice; or the safety reversing sensors are incorrectly installed.
The garage door will reverse open and WILL NOT close until the
OFF Button
obstructions are clear or the safety reversing sensors are correctly
installed. When the obstruction has been cleared or the safety reversing
sensors have been aligned, the door will close when the garage door
HOLD OPEN
opener is activated.
Button
Activate:
Press and hold the ON button until one of the TTC LEDs light up. Then
LIGHT
press the ON button again to cycle through the time interval options
Button
(the corresponding TTC LED will light for each time interval). The
garage door opener light bulbs will blink as confirmation.
Motion
Deactivate:
Sensor
Press and hold the OFF button until all TTC LEDs turn off and a beep is
heard from the control panel.
Temporarily hold door open (suspend TTC):
Press and release the HOLD OPEN button. The HOLD OPEN button will
begin to flash. Press the HOLD OPEN button again to resume normal
TTC operation.
LOCK
Activate*:
Press and hold the LOCK button for 2 seconds. The command LED will
flash as long as the lock feature is activated and your handheld remote
control will not operate your door at this time.
Deactivate:
Press and hold the LOCK button again for 2 seconds. The command
LED will stop flashing and normal operation will resume.
* Your Chamberlain
been activated.
4
ERASE DEVICES FROM MEMORY
4 ½ Erase all remote controls and keyless entries:
Minutes
1. Press and hold the LEARN button on the control panel until the red
learn LED goes out (approximately 6 seconds). All remote control
and keyless entry codes are now erased. Reprogram any
compatible accessory you wish to use.
Erasing remote controls and keyless entries from the control panel
NOTE:
does not erase them from the garage door opener, you need to erase the
memory of the garage door opener separately.
Erase all devices (including MyQ
1. Press and hold the LEARN button on the control panel until the red
learn LED goes out (approximately 6 seconds).
2. Immediately press and hold the LEARN button again until the red
learn LED goes out. All codes are now erased. Reprogram any
compatible accessory you wish to use.
3
® keypad will continue to work when LOCK has
® enabled accessories):