Casals FC14 Manual Del Usuario página 10

Locking button:
- To activate this function press button (B) while
holding down the start-up switch (A).
- To deactivate this function press the start-up (A)
switch right down.
Fitting the hinges (Fig 8)
- Choose a cutter with the same diameter as the width
of the hinge.
- Locate the hinge in the doorframe exactly in the
position where you wish to fit it.
- Mark the ends of the hinge and the intermediate
fitting as shown in the figure 8
- Graduate the depth as indicated in Section 4 of the
instructions for use.
- Graduate the moving base as indicated in Section 5
of the instructions for use.
- Penetrate the cutter frontally through one of the ends
of the hinge you have previously marked.
- Supporting the moving base well (H) on the frame,
slide the cutter towards the other end in a single pass.
- To make the intermediate fitting, tilt the router using
one of the ends of the moving base as a pivot.
- Move the router sideways over one of the ends
towards the area of the intermediate fitting.
- Cut the area of the intermediate fitting.
Use as a shaping tool (Fig 9)
The router can also be used as a conventional
shaping tool. To work with it as a shaping tool, you
must remove the moving base (H) as shown in
Section 2 of the instructions for use.
Use as an edge router for Formica (Fig 10)
The router with a moving base is ideal for removing
the excess from Formica sheets glued onto panels.
To do this, you need a conical cutter with hard metal
inserts.
- Any improper use or use not according to the
instructions for use may be dangerous, and invalidate
the guarantee and the manufacturer's responsibility.
Once you have finished using the appliance:
- Stop the appliance by releasing the on/off switch.
Cleaning
- Disconnect the appliance from the mains and allow it
to cool before undertaking any cleaning task.
- Clean the electrical equipment and the mains
connection with a damp cloth and dry. DO NOT
IMMERSE IN WATER OR ANY OTHER LIQUID.
10
- Clean the equipment with a damp cloth with a few
drops of washing-up liquid and then dry.
- Do not use solvents, or products with an acid or base
pH such as bleach, or abrasive products, for cleaning
the appliance.
- Do not let water or any other liquid get into the
air vents to avoid damage to the inner parts of the
appliance.
- Never submerge the appliance in water or any other
liquid or place it under running water.
- If the appliance is not in good condition of
cleanliness, its surface may degrade and inexorably
affect the duration of the appliance's useful life and
could become unsafe to use.
Supplies
- Always use original supplies, designed specifically
for your appliance model.
- These supplies are available in specialist shops.
Anomalies and repair
(Maintenance and servicing)
- Take the appliance to an authorised technical
support service if a product damage or other problems
arise. Do not try to dismantle or repair without
assistance, as this may be dangerous.
- If the connection to the mains has been damaged,
it must be replaced and you should proceed as you
would in the case of damage.
Specifications:
- Rated Power:
- Rated Voltage:
- No load Speed
- Clamp for milling cutters
- Maximum Longitudinal shift
- Cross slide shift
- Weight:
- Sound Pressure level (LpA): 83.0 dB(A), KpA = 3 dB(A)
- Sound Power level (LwA): 94.0 dB(A), KwA = 3 dB(A)
- Vibration:
NB: These specifications are subject to change
without notice of purpose of improvement.
- Measured sound level determined according
EN60745
- The vibration emission level given in this information
sheet has been measured according EN60745 and
may be used to compare one tool with other. It may be
used for a preliminary assessment of exposure
- The vibration value during actual use of the power
FC14
430W
230V
26.000 rpm
6mm
30mm
28mm
1.8 Kg
7.7 m/s2, K= 1.5 m/s2