Initial Operation; Important; The Ma600's Menu; Tube Replacement - Magnat MA 600 Información Importante Sobre La Instalación / Certificado De Garantía

INITIAl OPeRATION

i
• Place the MA 600 on an even surface. Observe the relevant clearance gaps as specified under
"Important safety instructions".
IMPORTANT: Do not place any objects on top of the device (magazines, cD/record cases, etc.).
The ventilation slots located on top of the device must be unobstructed at all times!
• connect your speakers:
The stereo speakers (impedance of 4 to 8 ohms) are connected to the rear as follows:
Only use high-quality audio speaker cables with a conductor cross section of min. 1.5 - 2.5 mm². Strip
approx. 10 mm from the cables and twist the ends. Loosen the terminal screws one after the other and
insert the stripped ends into the holes. Re-tighten the terminal screws. Make sure you pay attention
to the correct polarity.
You can also use prefabricated cables with 4mm banana plugs or forked fittings.
Also observe the operating instructions for the speakers you are using.
• connect your audio sources.
• connect the supplied mains cable to the rear and then insert the other end into a 230V socket.
• Actuate the on/off switch on the rear side, the device is now in the standby mode.
• Now switch on the device using the remote control or with the ON/STBY key on the front.
• When the tube has heated up the device is ready for use.
• Select your desired audio source using the input selector switch.

CONNeCTING THe DeVICe TO A BlUeTOOTH AUDIO SOURCe

Select Bluetooth input. If you have previously connected a Bluetooth device, the MA 600 will
automatically attempt to re-establish a connection with this device. If this is the case, you may be
required to manually reconfirm the connection on the source device.
If a connection has not already been made or the connection cannot be re-established, the MA 600
will automatically activate the ‚pairing mode'. „BT" will flash on the display.
Now activate the Bluetooth mode on your source device. The MA 600 will appear in the list of
Bluetooth devices as „MA 600". If it is not displayed in the list, set your source device to search for
Bluetooth devices manually and make sure that the MA 600 has been switched to the pairing mode.
Depending on the source device, you may be asked whether the password is to be accepted during
the pairing procedure. You can confirm this by simply pressing „Accept". If you are still asked for
a password, use the default passwords „0000" or „1234". If you are asked if you want to establish
a connection after pairing, please select „Yes". When the device has been paired and connected
successfully the „BT" indicator will illuminate continuously.
The MA 600 supports the „aptx®" high quality audio transmission standard. If your source device
also supports this standard, „aptx®" will be selected automatically as the transfer mode when
establishing a Bluetooth connection.
THe MA 600´S MeNU
The tone and the inputs' input sensitivity may be comfortably adjusted via a menu.
• The menu can be accessed by pressing the volume knob on the front of the unit.
• To navigate within the menus and to change the settings turn the volume knob.
• confirm the individual menu items by pressing the volume knob.
The following settings are possible:
• Bass adjustment:
Select BASS in the menu. Bass playback may be ramped either up or down in five steps.
• Treble adjustment:
Select TREBLE in the menu. The treble setting may be ramped either up or down in five steps.
• Balance adjustment:
Select BALANcE in the menu. The stereo balance may be adjusted either to the right or left in
ten steps.
• Input sensitivity:
Select INPUTGAIN in the menu. Now the input sensitivity for the currently selected input may be
increased in four steps. This enables you to adapt audio sources with lower output levels to other
audio sources.
The RESET menu item will restore the basic settings (all tone settings to 0 and input sensitivity for all
inputs to 0 dB).
You can leave the menu via EXIT.

TUBe RePlACeMeNT

The device has a high quality preamplifier stage which is equipped with two tubes. The tubes have a
very long service life when used under normal operating conditions (min. 20,000-50,000 hours).
If it is necessary to replace the tubes, please refer to a specialist dealer.

SeRVICe AND TeCHNICAl PROBleMS

If you should encounter any technical problems, please contact your specialist dealer or
Magnat Audio-Produkte GmbH, Tel.: 02234807-0.
12