Description Of Symbols - Silverline 269131 Manual De Instrucciones

GB

Description of Symbols

The rating plate on your tool may show symbols. These represent important
information about the product or instructions on its use
Wear hearing protection
Wear eye protection
Wear breathing protection
Wear head protection
Wear hand protection
Read instruction manual
Caution!
DO NOT use on scaffolding or ladders
Important safety devices! Ensure correct function, maintain in
accordance with instructions and DO NOT disable!
DO NOT use with compressed gas cylinders!
Conforms to relevant legislation and safety standards
Environmental Protection
Air tools must not be disposed of with household waste. Air
tools may contain traces of tool oil and other lubricants and so
must be recycled accordingly
Specifications
Working pressure ....................................... 4 – 7bar
Maximum pressure .................................... 7.5bar (108psi)
Air inlet .......................................................
Nail/staple size....................brad nails: 18 Gauge, 10 – 32mm
Magazine capacity ..................................... 100 nails/staples
Weight ........................................................ 1.1kg
Sound and Vibration Information:
Sound pressure L ..................................... 95.5dB(A)
PA
Sound power L ........................................ 82.5dB(A)
WA
Uncertainty K .............................................. 3dB
Weighted vibration ..................................... 2.0m/s
Uncertainty K .............................................. 29.63%
As part of our ongoing product development, specifications of
Silverline products may alter without notice.
The sound intensity level for the operator may exceed 85dB(A) and
sound protection measures are necessary.
4
(60 – 100psi)
⁄ " BSP quick
1
4
connector
staples:18 Gauge, 13 – 32mm
2
0.079"(2mm)
10mm(3/8")
15mm(5-8")
20mm(3/4")
25mm(1")
30mm(1-3/16")
32mm(1-1/4")
1.26 X 1.05mm
(0.050")(0.041")
Calibro 18
18Ga.
WARNING: Always wear ear protection where the sound level exceeds 85dB(A) and
limit the time of exposure if necessary. If sound levels are uncomfortable, even with ear
protection, stop using the tool immediately and check the ear protection is correctly fitted
and provides the correct level of sound attenuation for the level of sound produced by
your tool.
WARNING: User exposure to tool vibration can result in loss of sense of touch, numbness,
tingling and reduced ability to grip. Long term exposure can lead to a chronic condition. If
necessary, limit the length of time exposed to vibration and use anti-vibration gloves. Do
not operate the tool with hands below a normal comfortable temperature, as vibration will
have a greater effect. Use the figures provided in the specification relating to vibration to
calculate the duration and frequency of operating the tool.
Sound and vibration levels in the specification are determined according to EN60745 or
similar international standards. The figures represent normal use for the tool in normal
working conditions. A poorly maintained, incorrectly assembled, or misused tool may
produce increased levels of noise and vibration. www.osha.europa.eu provides information
on sound and vibration levels in the workplace that may be useful to domestic users who
use tools for long periods of time.
Carefully read and understand this manual and any label attached to the tool before use.
Keep these instructions with the product for future reference. Ensure all persons who use
this product are fully acquainted with this manual.
Even when used as prescribed it is not possible to eliminate all residual risk factors. Use
with caution. If you are at all unsure of the correct and safe manner in which to use this
tool, do not attempt to use it.
General Safety Warnings
WARNING Read all safety warnings and all instructions. Failure to follow the warnings
and instructions may result in electric shock, fire and/or serious injury.
WARNING: This appliance is not intended for use by persons (including children) with
reduced, physical or mental capabilities or lack of experience or knowledge unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children must be supervised to ensure that they do not play
with the appliance.
Save all warnings and instructions for future reference.
1) Work Area Safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate tools in explosive atmospheres, such as in the presence of
flammable liquids, gases or dust.
c) Keep children and bystanders away while operating a powered tool. Distractions
can cause you to lose control.
2) Personal Safety
a) Stay alert, watch what you are doing and use common sense when operating a
powered tool. Do not use a powered tool while you are tired or under the
influence of drugs, alcohol or medication. A moment of inattention while operating a
powered tool may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position when not
operating the tool and make use of other safety features which prevent unintentional
starting
d) Remove any adjusting key or wrench before turning the powered tool on. A
wrench or a key left attached to a rotating part of the tool may result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables better
control of the tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and
gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in
moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection can
reduce dust-related hazards.
1/4"(5.7mm)
13mm(1/2")
16mm(5-8")
19mm(3/4")
25mm(1")
32mm(1-1/4")
1.26 X 1.05mm
(0.050")(0.041")
Calibro 18
18Ga.