Initial Operation - Leifheit AirActive L Steamer Manual Del Usuario

Initial operation

B
I
In order to ensure sufficient ventilation, the distance
of the device to a wall or other objects must be at
least 15 cm on the back of the device and 15 cm on
the sides.
The steam ironing board must be placed on a solid,
1. Hold the complete system with both hands and use
the operating lever (5) to position it: lift the lever
with one hand and raise the complete ironing
table. The table is locked only after a clicking
noise can be heard.
The steam iron system can be adjusted to six different
heights (max. height 100 cm).
2. Unwind the power supply cable [1] for the steam
ironing system.
3. Only rest iron on the area with the specially design
silicone knobs [15] on the pressure steam station.
4. Clip cable holder [20] into the intended bracket
on the rail of the steam station.
5. Clamp feed hose [16] into the cable holder.
II
To fill up the pressure steam station with
water, please proceed as follows:
Remove main plug [1] and [7] from power
socket.
First fill water refilling cup [21] up with water.
(Note advice on this below!)
Unscrew the safety lock [8] on the filler opening. If the
pressure steam station has already been used before,
press safety lock [8] first and carefully twist 1/2 a
turn, while keeping lock pressed to permit any
pressure inside to escape safely.
Then unscrew completely.
Use filling cup [21] to fill 1 litre or regular tap water
into the water tank of the steam station (observe note
regarding filling with water)!
Avoid overfilling the steam generator (1 litre
max.). Overfilling may cause hot water instead
of steam to be emitted.
If water leaks or if the tank is overfilled, please
remove some water and dry the device thoroughly.
Screw on safety lock [8] securely to avoid steam from
escaping accidentally.
38
III
1. Insert the power plug [7] of the steam ironing
station into the power outlet on the side of the
ironing table, which is designed for this purpose.
This will ensure power supply for the
steam ironing station.
2. Then insert the power plug of the power cord
[1] of the complete system into a wall outlet.
IV
1. Turn on switch for steam iron [10].
2. Then turn on switch for steam generator [9].
Caution:
Always check that there is sufficient water in the
steam boiler before operating the steam ironing station
(1 litre max.).
We, therefor, recommend topping up the boiler with
water before every use. This way, you will avoid having
to refill the boiler while you're ironing.
Wait a few minutes until the green pilot light for steam
ready [12] turns and the ironing surface is hot.
3. Then turn on the On/Off switch [3] to start the
steam extraction of the steam iron board.
We recommend activating the steam extraction
function regularly to remove any residual steam left
in the unit housing. Activating the blow-up function
and steam extraction function regularly warrants
maximum heat and dryness while you iron.
(Please observe the notes for steam extraction
and blow-up function on page 40)
4. Set temperature control dial [17] of iron to
When ironing with steam please ensure that the
temperature for the iron is not set below
the mark .
The iron is ready to use when the control lamp [19]
lights up.
5. The laundry may now be steamed by using the
steam button [18]. Release the steam button if
steam is no longer required.
Lock the steam button for continuous steam by
pushing the button down while simultaneously
pushing it toward the front.
6. Use the steam volume regulator (14) to adjust the
steam volume. It can be adjusted continuously.
(Please refer to ironing recommendations,
page 39!)
V
If you need to top up the unit with water,
please proceed as follows:
Warning lamp of water level indicator [11] will
light up.
1. Switch of steam generator by pushing switch [9].
2. Force out residual steam by pushing the steam
emission button on the iron [18].
3. Switch off iron by pressing button [10].
4. Remove mains plug [1].
5. Carefully open safety valve [8] by twisting plug by
1/2 a turn (CAUTION: pressurised hot steam may
escape!) and slowly unscrew plug.
Warning: If the unit is being operated for a long time,
the valve can become very hot. Allow the unit to cool off
or use a cloth when opening the valve.
Allow pressure steam station to cool off for a few
minutes.
6. Then refill unit with water and switch pressure
steam station back on.
(See to Initial operation )
III IV
When first taking the iron into use, a slight smell of
burning and some smoking is to be seen as normal. The
reason for this is the adjustment in the seals and the
material to the temperature.
For this reason, please do not use the first jets of steam
on the material to be ironed, but on a cloth instead.
Please take note of the recommendations and advice
for the best possible use of the
steam extraction
blow-up function
for the steam ironing board found under Ironing Tips
on Page 40.