Descargar Imprimir esta página

Fender Cyber Foot Controller Instrucción De Funcionamiento página 4

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

The Fender
®
Cyber Foot Controller™ can be used to
send Program Change and Continuous Controller
messages to any MIDI device, hands-free. Especially
designed to complement Fender Cyber-Series™
amplifiers, the Cyber Foot Controller adds functionality
to any amp that interprets the following messages of the
MIDI specification, (features as they relate to Cyber-
Series amps shown in brackets):
◊ Program Change messages: Use the DOWN and
UP buttons to index by "tens," then a 0–9 button to
select the "ones" digit. [Selects any preset using the
MIDI map.]
◊ Continuous
Controller
CONTINUOUS CONTROLLER pedal to send Control
Change messages. [Adjusts a preset parameter
defined by your amplifier.]
C C
C C
A.
TAP TEMPO / TUNER BUTTON
Sets the time/rate parameter for the active effect
with one or more quick presses. A single press will
set the parameter to its maximum value.
or
Activates the TUNER Mode when held down for 2
seconds, ("tun" is displayed). Press any button to
exit TUNER Mode.
Sends a Program Change message to Bank 1,
Program 127.
1
B.
EFFECTS ON (OFF) BUTTON
Alternately engages and bypasses the effects for
the current preset.
Continuous Controller assignment: 85.
Sends alternating Control Change messages:
Data 0 for OFF; Data 127 for ON.
C.
LED DISPLAY
•Displays the last Program Change number
transmitted (flashes "
number is selected).
•Displays "tun" in TUNER Mode.
•Displays MIDI Transmit Channel during selection.
MIDI TRANSMIT CHANNEL SELECTION
Transmit channel is set to 1 by default at power-up. To
select
channels
(1–16):
TAP TEMPO/TUNER {A}, press EFFECTS ON {B}, then
1
Bank Change #1 is used only to access the TUNER Mode, all other messages ar e prefaced with Bank Change #0, which corresponds
to the MIDI Map on Fender® Cyber-Series™ amplifiers.
w
w w
w w
w . . f f e
e n
n d
F F
e e
a a
t t
u u
r r
e e
F F
e e
a a
t t
u u
r r
e e
messages:
Use
y y
b b
e e
r r
– –
S S
e e
r r
i i
y y
b b
e e
r r
– –
S S
e e
r r
i i
" until the first
00_
While
holding
d e
e r
r . . c
c o
o m
m
s s
• •
O
O
v v
e e
r r
v v
s s
• •
O
O
v v
e e
r r
v v
◊ Volume control messages: Use the VOLUME pedal
to adjust the volume on your amplifier. [Adjusts
master volume.]
Cyber-Series™ messages (unspecified MIDI messages
that may be interpreted differently by other amps.)
◊ TAP TEMPO/TUNER BUTTON
•Set the time/rate parameter for the current effect
• Activate the on-board tuner.
◊ EFFECTS ON BUTTON
•Engage or bypass the current preset's effect.
the
Thank you for choosing Fender
Thank you for choosing Fender
—T
one, T
radition and Innovation—since 1946.
—T
one, T
radition and Innovation—since 1946.
e e
s s
M
M
I I
D
D
I I
F F
u u
e e
s s
M
M
I I
D
D
I I
F F
u u
is not transmitted until the "ones" digit is selected (see
item {E} below). Note: The display stops flashing when a
DOWN or UP selection returns you to the interval
containing the last Program Change number transmitted.
0, 1, 2, 3, 4, 5, 6, 7, 8, 9
E.
Selects the "ones" digit of the Program Change
number within the pre–selected "tens" range, and
transmits the Program Change number.
example, if the display shows, "12_," pressing the
"7" button will cause "127," to display and the
Program Change 127 to transmit.
Note: "128" and "129" cannot be selected.
F.
CONTINUOUS CONTROLLER PEDAL
Controls any programmable parameter for the
current preset.
Continuous Controller assignment: 11.
Sends Control Change messages 0–127.
G.
VOLUME PEDAL
Controls the MASTER volume level.
Continuous Controller assignment: 7.
Sends Control Change messages 0–127.
release both buttons. Select a channel using the
down
DOWN and UP buttons {D}, (channel selection is
displayed). Press any "0–9" button to exit.
4
w
w w
w w
w . . m
m r
i i
e e
w w
i i
e e
w w
,
®
®
,
n n
c c
t t
i i
o o
n n
s s
n n
c c
t t
i i
o o
n n
s s
D. DOWN (–10) & UP (+10)
BUTTONS
Pre-selects the "tens"
range for a Program
Change number at these
intervals:
000↔0 10↔020↔030↔
040↔050↔060↔0 70↔
0 8 0 ↔ 0 9 0 ↔ 1 0 0 ↔ 1 1 0 ↔
120↔000↔
A Program Change number
BUTTONS
r g
g e
e a
a r
r h
h e
e a
a d
...
(loop)
For
d . . n
n e
e t
t

Publicidad

loading

Este manual también es adecuado para:

Pr 466