Turning The Power Off; Listening To The Demo Performances; Connecting And Playing Instruments - Korg KR-55 Pro Guia De Inicio Rapido

3. In System mode, specify the type of batteries that you're
using.
(Default setting aL: Alkaline batteries)
If you switch to using a different type of battery, be sure to
specify the correct battery type in System mode.
See "[M1] Battery type "batt"" on page 23 of the
Owner's Manual
Replacing the batteries
Replace the batteries when the power button blinks.
As the batteries run low, you might hear noise or
interruptions in the sound.
Unusable batteries should be removed immediately. If
unusable batteries are left installed in the unit, they may leak,
causing malfunctions. You should also remove the batteries if
you don't plan to use the unit for an extended time.
Be sure to replace all six batteries together as a set. Do not
mix fresh batteries with used batteries in the same set.
Turning the power on
Note: If a device is connected to the AUX IN jack, turn its
power on before you continue.
Note: If you're using an SD card, insert it into the SD card slot
before you turn on the power (see page 6 "Inserting or
removing an SD card").
1. On the top panel, set the VOLUME knob to the
minimum level (far left).
2. On the top panel, hold down the power button for at
least one second to make the button light.
When the KR-55 Pro finishes starting up, it is ready to
produce sound.
3. Turn on the power of the external equipment that is
connected to the KR-55 Pro's OUTPUT L/MONO and R
jacks, such as powered monitor speakers.
4. Adjust the volume on the external output device and on
the KR-55 Pro.

Turning the power off

Never turn off the power or disconnect the AC adapter
during recording, while data is being converted, or while
data is being written to the system.
Doing so may make the KR-55 Pro malfunction, or
damage the data on the SD card. If the data on the SD card
has been damaged, format the card.
1. If recording or playback is occurring, press the
[ ] button to stop.
2. Hold down the power button for one second or longer
until the button blinks.
After a time, the power button and display indication will
go dark, and the KR-55 Pro will shut down.
Use caution when turning off the power!
To turn off the power of the KR-55 Pro, you must press the
power button located on the panel. (When you do this, the
KR-55 Pro saves its data.)
Never disconnect the AC adapter or remove the batteries
while the power is on.

Listening to the demo performances

Auto Power-Off
The KR-55 Pro has an auto power-off function. The auto
power-off function automatically turns off the power when
there has been no user input for a certain length of time
(which you can specify).
(See "[M3] Auto power-off function "APOF"" on page 23 of
the Owner's Manual.)
Listening to the demo
performances
The KR-55 Pro contains demo song data. Let's start by
listening to the sound of the KR-55 Pro.
4
1
1
1. Simultaneously press the [SYSTEM] button and [Count
Start] button to enter Demo mode.
The [SYSTEM] button and [Count Start] button blink, and
the demo song plays.
The top panel buttons light in synchronization with the
demo song.
2. Use the VOLUME knob to adjust the volume of the
demo song.
3. You can press the [ ] or [
previous or next demo song.
4. To exit Demo mode, press any one of the mode buttons
[RHYTHM], [RECORDER], [PLAYER], or [SYSTEM].
Connecting and playing
instruments
The KR-55 Pro provides a mic input, two inputs for guitar or
bass, and an AUX input, allowing multi-channel mixing. A
variety of input sources are supported, including guitar, bass
guitar, and a microphone.
2
3
] buttons to play the
7