Whale Supersub Smart 1100 Manual De Instrucciones página 2

2
EN
Thank you for purchasing this Whale product.
For over 40 years Whale has led the way in the design and manufacture of freshwater, bilge and waste systems including:-
plumbing, taps, showers and pumps, for low voltage applications. The company and its products have built a reputation for quality,
reliability and innovation backed up by excellent customer service.
For information on our full product range visit: www.whalepumps.com
CONTENTS
1. Principles of Operation 6. Instructions for use
2. Application 7. Trouble shooting
3. Warning 8. Winterization
4. Optional Extras 9. Service Support & Warranty
5. Installation Instructions
To the fitter
Read the following carefully before installation.
Check that the product is suitable for the intended application, follow these installation instructions and ensure all relevant
personnel read the points below. Also ensure that these operating instructions are passed on to the end user.
WARNING: Please note that incorrect installation may invalidate warranty.
To the user
Read the following instructions carefully.
1. Principles of Operation
OF OPERATION
All Supersub models, Supersub 500 and 1100 and Supersub Smart 650 and 1100 are uniquely designed, specifically for fast and
efficient removal of bilge water from leisure craft. The Supersub range fits into narrow and low spaces that other bilge pumps can-
not reach. THE SUPERSUB 500 AND 1100 ARE NOT AUTOMATIC PUMPS. (Please refer to section 4 for the switches and optional
extras that can be used with these products)
Supersub Smart 650 and 1100 are fully automatic. The pump will become aware of the presence of water and will switch on the
pump, turning it off again when the water level has dropped. The switching is solid state hence there are no moving parts. The
Supersub Smart models allow waves of water to pass over, without turning the pump on every time, as it has a built in time delay.
2. Application
• The Supersub range of products are designed to pump normal bilge water. Output capacity depends on installation and operating
conditions. If this product is intended to be used for any other purpose or with any other liquid, it is the user's responsibility to ensure that
the pump is suitable for the application and, in particular, that the materials are fully compatible with the liquids to be used.
• This product must only be used in the bilges of leisure craft. If this product is to be used as the sole and/or primary bilge pump, the
Supersub 500/1100 and Supersub Smart 650/1100 pumps should only be used in boats up to 24m (78.8 ft).
• The bilge water should only be evacuated through a correctly installed skin fitting above the water line of the boat.
3. Warning
The Supersub range of products is designed only for the removal of normal bilge water in leisure boats and personal watercraft
(As explained in Application). Your warranty may be invalidated if the product is used in other applications or outside the remit of
the standards quoted on the packaging and pump body.
Do NOT screw the pump directly onto the hull.
The pumped water must be evacuated through a skin fitting above the water line (see typical installation diagrams). The Supersub
range is not for use in systems evacuating water through a skin fitting or seacock below the water line. All pipework must contain
a correctly installed anti-syphon valve / loop.
4. Optional Extras
LV1219 - Non-return Valve (recommended for Supersub 500 and Supersub Smart 650) .
BE9001 - Automatic, water activated, electronic switch (For use with Supersub 500 and 1100).
BE9002 - Automatic, water activated, floatswitch (Please see Figure 3, Supersub 500 Automatic System).
SF5131 - 3/4" Skin fitting (Supersub 500 and Supersub Smart 650)
SF5204 - 1" Skin Fitting (Supersub 1100 and Supersub Smart 1100)
5. Installation Instructions
See diagrams (page 4)
Munster Simms Engineering Ltd, Old Belfast Road, Bangor, Co Down, N. Ireland BT19 1LT
Tel: +44 (0)28 9127 0531 Fax: +44 (0)28 9146 6421
Web: www.whalepumps.com Email info@whalepumps.com
Supersub Supersub
Range Range
LIST OF IMAGES
Figure 1. Installation
Figure 2. Installation Instructions
Figure 3. Fitting Instructions
Figure 4. Wiring diagrams
Figure 5. Plumbing
Figure 6. Maintenance