Ryobi RCS1935 Traducción De Las Instrucciones Originales página 5

or its own cord. Saw chains contacting a "live" wire
may make exposed metal parts of the power tool "live"
and could give the operator an electric shock.
Wear safety glasses and hearing protection. Further
protective equipment for head, hands, legs and feet
is recommended. Adequate protective clothing will
reduce personal injury by flying debris or accidental
contact with the saw chain.
Do not operate a chainsaw in a tree. Operation of
a chainsaw while up in a tree may result in personal
injury.
Always keep proper footing and operate the
chainsaw only when standing on fixed, secure and
level surface. Slippery or unstable surfaces such as
ladders may cause a loss of balance or control of the
chainsaw.
When cutting a limb that is under tension be alert
for spring back. When the tension in the wood fibres is
released the spring loaded limb may strike the operator
and/or throw the chainsaw out of control.
Use extreme caution when cutting brush and
saplings. The slender material may catch the saw
chain and be whipped toward you or pull you off
balance.
Carry the chainsaw by the front handle with the
chainsaw switched off and away from your body.
When transporting or storing the chainsaw always
fit the guide bar cover.
chainsaw will reduce the likelihood of accidental contact
with the moving saw chain.
Follow instructions for lubricating, chain tensioning
and changing accessories. Improperly tensioned
or lubricated chain may either break or increase the
chance for kickback.
Keep handles dry, clean, and free from oil and
grease. Greasy, oily handles are slippery causing loss
of control.
Cut wood only. Do not use chainsaw for purposes
not intended. For example: do not use chainsaw
for cutting plastic, masonry or non-wood building
materials. Use of the chainsaw for operations different
than intended could result in a hazardous situation.
Causes and operator prevention of kickback:
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and pinches
the saw chain in the cut.
Tip contact in some cases may cause a sudden reverse
reaction, kicking the guide bar up and back towards the
operator.
push the guide bar rapidly back towards the operator.
Either of these reactions may cause you to lose control of
the saw which could result in serious personal injury. Do
not rely exclusively upon the safety devices built into your
saw. As a chainsaw user, you should take several steps to
keep your cutting jobs free from accident or injury.
Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be avoided by
taking proper precautions as given below:
Maintain a firm grip, with thumbs and fingers
encircling the chainsaw handles, with both hands
on the saw and position your body and arm to allow
you to resist kickback forces. Kickback forces can
be controlled by the operator, if proper precautions are
taken. Do not let go of the chainsaw.
Do not overreach and do not cut above shoulder
height. This helps prevent unintended tip contact and
enables better control of the chainsaw in unexpected
situations.
Only use replacement bars and chains specified
by the manufacturer. Incorrect replacement bars and
chains may cause chain breakage and/or kickback.
Follow the manufacturer's
maintenance instructions for the saw chain.
Decreasing the depth gauge height can lead to
increased kickback.
ADDITIONAL CHAINSAW SAFETY WARNINGS
when operating the product the first time.
Ensure all guards, handles and spiked bumper are
properly fitted and are in good condition.
The chainsaw is a heavy unit so the operator requires
to be physically fit. The operator should be alert, have
good vision, mobility, balance and manual dexterity. If
there is any doubt, do not operate the chainsaw.
Do not start using the product until you have a clear
work area, secure footing, and a planned retreat path
away from the falling tree.
Beware of the emission of lubricant mist and saw dust.
Wear a mask or respirator if required.
Electric power should be supplied via a residual current
30 mA.
If the power cable becomes damaged, you must return
the machine to an authorised service centre for repair
or replacement.
Always keep the power cable tidy and away from the
area of cutting. Apart from the danger of electrocution,
untidy cables cause falls and trips.
Always hold the chainsaw with both hands when
operating the saw. Use a firm grip with thumbs and
fingers encircling the chainsaw handles. Right hand
must be on the rear handle and left hand on the front
handle.
Before starting the tool, make sure the saw chain is not
contacting any object.
Do not modify your tool in any way or use it to power
any attachments or devices not recommended by the
manufacturer for your saw.
wound dressings and a means to summon attention
comprehensive kit should be reasonably nearby.
The operator may be tempted to remove the helmet if
EN
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
sharpening and
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
English | 3