Ryobi OPP1820 Traducción De Las Instrucciones Originales página 3

Safety, performance, and dependability have been given
top priority in the design of your cordless pole saw.
INTENDED USE
The cordless pole saw is only intended for use outdoors.
For safety reasons, the product must be adequately
controlled by using two-handed operation.
The product is designed for cutting and pruning of small
limbs and branches whose diameter is less than or equal
to the bar length, and are located high in the tree while
the operator maintains a steady footing on the ground. The
product is designed to be extended to a maximum length of
3 m. Do not exceed this working length.
It is not intended to be used while climbing or as a
conventional chainsaw for close quarter limbing and
pruning of material at ground level.
GENERAL SAFETY WARNINGS
WARNING
Read all safety warnings and all instructions. Failure
to follow the warnings and instructions may result in
electric shock, f re and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool'' in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
WORK AREA SAFETY
■ Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
■
Do not operate power
atmospheres, such as in the presence of flammable
liquids, gases or dust. Power tools create sparks,
which may ignite the dust or fumes.
■
Keep children and bystanders away while operating
a power tool. Distractions can cause you to lose control.
ELECTRICAL SAFETY
■
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any adapter
plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk
of electric shock.
■
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
■
Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of
electric shock.
■
Do not abuse the cord. Never use the cord for
■
■
PERSONAL SAFETY
■
■
■
■
■
tools in explosive
■
■
POWER TOOL USE AND CARE
■
■
■
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges, or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of electric shock.
If operating a power tool in a damp location is
unavoidable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol, or medication. A
moment of inattention while operating power tools may
result in serious personal injury.
Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce
personal injuries.
Prevent unintentional starting. Ensure the switch
is in the off-position before connecting to power
source and/or battery pack, picking up, or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
Remove any adjusting key or wrench before turning
the power tool on. A wrench or a key left attached to a
rotating part of the power tool may result in personal injury.
Do not overreach. Keep proper footing and balance
at all times. This enables better control of the power
tool in unexpected situations.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves away
from moving parts. Loose clothes, jewellery or long
hair can be caught in moving parts.
If devices are provided for the connection of dust
extraction and collection facilities, ensure these are
connected and properly used. Use of dust collection
can reduce dust-related hazards.
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not use the power tool if the switch does not turn
it on and off. Any power tool that cannot be controlled
with the switch is dangerous and must be repaired.
Disconnect the plug from the power source and/or
the battery pack from the power tool before making
EN
English
FR
DE
ES
IT
NL
PT
DA
SV
FI
NO
RU
PL
CS
HU
RO
LV
LT
ET
HR
SL
SK
BG
UK
TR
1