Transportation And Storage - Ryobi OPP1820 Traducción De Las Instrucciones Originales

Footwear
– should comply with EN 20345 and be CE marked
OPERATION
■ Study the condition of the tree and branches before
starting work. If there are signs of damage, rot or decay,
do not attempt to prune yourself. Damaged or rotten
branches are highly unstable. Seek the services of a
professional tree surgeon.
■ Never stand under the branch to be pruned.
■ Pruned branches do not always fall cleanly to the
ground. They are easily caught and deflected by
other foliage. Ensure that a safety zone at least twice
the length of the branch to be cut is available and
maintained during your pruning. If this is not possible,
seek the services of a professional tree surgeon.
■ Ensure that the falling branch is not a danger to
yourself, bystanders or property, including utility cables.
■ Never operate the product with the pole at an angle of
greater than 60° from the horizontal.
■ Never operate the product with the cutting means
closer than 10 m from overhead power lines.
■ Do not force the product, let the chain do the work at
its own speed.
■ Do not try to cut the branch too close to the tree trunk.
Leave about 15 cm from the trunk to the cut.
■ Rest the saw bar on the branch to be pruned and push
the saw gently forwards so that the ribbed bumper also
contacts the branch. This will aid stability, cutting, and
provide cleaner cuts.
■ Small and thin branches that are not heavy can be cut with
one cut using the bottom of the saw bar.
■ Branches with larger diameter and are heavier may
break or split during the cut so the user must make a
first cut from under the branch using the top of the saw
bar. The first cut should be approximately one-third of
the way through the branch.
■ Consider pruning large branches in manageable
sections rather than as a whole.
■ Never try to restart a previous cut with the chain and
bar in the earlier cut. Always start a new cut. This will
reduce the risk of kickback and potential injury.

TRANSPORTATION AND STORAGE

■ Stop the product, remove the battery pack, and allow it
to cool before storing or transporting.
■ Clean all foreign materials from the product. Store it in
a cool, dry and well-ventilated place that is inaccessible
to children. Keep away from corrosive agents, such
as garden chemicals and de-icing salts. Do not store
outdoors.
■ Cover the saw bar with the scabbard before storing or
4
transporting the product.
■ When storing the product for a long period of time (one
month or longer), be sure the chain is lightly lubricated
to prevent rust. The manufacturer recommends the use
of Ryobi bar and chain lubricant, which is available at
your Ryobi authorised service center.
■ For transportation, secure
movement or falling to prevent injury to persons or
damage to the product.
MAINTENANCE
WARNING
Use only original manufacturer's replacement parts,
accessories, and attachments. Failure to do so can
cause possible injury, poor performance, and may void
your warranty.
WARNING
Servicing requires extreme care and knowledge
and should be performed only by a qualif ed service
technician. For service, we suggest you bring the
product to your nearest authorised service center. When
servicing, use only identical replacement parts.
WARNING
The saw chain is very sharp. To prevent personal injury,
exercise extreme caution when cleaning, f tting, or
removing the chain scabbard. Always wear protective
gloves when performing maintenance on the chain.
WARNING
Improper chain maintenance increases the potential of
kickback. Failure to replace or repair damaged chain can
cause serious injury.
■ Switch off and remove the battery pack before
conducting any maintenance or cleaning work.
■ You may only make adjustments or repairs described
in this manual. For other repairs, contact the authorised
service agent.
■ Follow instructions for lubricating and chain tension
checking and adjustment.
■ After each use, clean the body and handles of the
product with a soft dry cloth.
■ Check all nuts, bolts and screws at frequent intervals
for proper tightness to ensure the product is in safe
working condition. Any part that is damaged should be
properly repaired or replaced by an authorised service
center.
English
the product against