Before Starting The Equipment; Using The Equipment - Robust 1100/1 Manual De Instrucciones Original

Anleitung_RB_PO_1100_1_SPK7__ 23.07.14 15:36 Seite 18
GB
Vibration emission value a
K uncertainty = 1,5 m/s 2
Operating mode: Sanding with sanding paper
Vibration emission value a
K uncertainty = 1,5 m/s 2
Operating mode: Polishing
Warning!
The specified vibration value was established in
accordance with a standardized testing method. It
may change according to how the electric equipment
is used and may exceed the specified value in
exceptional circumstances.
The specified vibration value can be used to compare
the equipment with another electric power tools.
The specified vibration value can be used for initial
assessment of a harmful effect.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect working
n
order.
Service and clean the appliance regularly.
n
Adapt your working style to suit the appliance.
n
Do not overload the appliance.
n
Have the appliance serviced whenever
n
necessary.
Switch the appliance off when it is not in use.
n
Wear protective gloves.
n

6. Before starting the equipment

Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
6.1 Assembly (Fig. 4-7)
Important! Pull out the mains power plug before
starting the assembly work.

7. Using the equipment

Secure your workpiece. Make sure that the
workpiece is held securely by a clamping device or a
vise.
7.1 Switching the equipment ON/OFF
The equipment is turned on (I) and off (0) with the
ON/OFF switch (Fig. 3 / Item 3). However, the
equipment will only start running after the speed
control has been activated (see section 7.4).
18
= 13,47 m/s 2
h/DS
= 11,55 m/s 2
h/P
7.2 Using as a polishing machine
When using waxing and polishing agents,
observe the instructions issued by their
manufacturer!
IMPORTANT!
To prevent damage to the surfaces of the workpieces
you wish to polish, make sure that you observe the
following instructions:
Make sure that the polishing attachment is always
n
mounted precisely in the center of the
sanding/grinding disk.
Before you start the equipment, check to ensure
n
that the attachments are securely installed.
Never touch the area you wish to polish with the
n
edge of the sanding/grinding disk.
Use the speed selector (Fig. 3/Item 4) to select the
n
following maximum speeds for polishing:
- Working in polish:
- Polishing to a high gloss: approx. 1000-1100 rpm
- Polishing up:
If you do not comply with these instructions, the
manufacturer cannot accept any liability.
The Velcro fastener enables easy changing of the
polishing attachment.
- Use the foamed plastic attachment to apply the
polishing agent (Fig. 8).
Make sure that the foamed plastic attachment is
n
free of any foreign bodies.
Spread the polishing paste evenly over the
n
polishing pad. Do not apply the polish directly to
the polishing surface.
Switch the polishing machine on and off only
n
when the polishing machine is resting on the
polishing surface.
Place the extension lead over your shoulder and
n
work first on the large, flat surfaces such as the
bonnet, boot lid and roof.
Keep your movements as regular as possible.
n
Important! Allow the polishing machine to glide
n
over the polishing surface. Do not exert pressure!
Work next on the smaller surfaces (doors, for
n
example)
- Use the fleece attachment to finish off the polishing
(Fig. 9).
Make sure that the fleece attachment is free of all
n
foreign bodies.
Remove the layer of polish in the same order as it
n
was applied.
Important! Do not exert pressure on the
n
polishing machine!
approx. 1000 rpm
approx. 1400 rpm