Publicidad
Idiomas disponibles
Idiomas disponibles
3 41 01 118 06 0.book Seite 18 Mittwoch, 5. März 2014 10:27 10
en
18
Handling hazardous dusts
For work procedures with this power tool where mate-
rial is removed, dusts develop that can be hazardous to
one's health.
Contact with or inhaling some dust types, e. g. asbestos
and asbestos-containing materials, lead-containing coat-
ings, metal, some wood types, minerals, silicate particles
from materials containing stone, paint solvents, wood
preservatives, and antifouling paints for vessels, can trig-
ger allergic reactions to the operator or bystanders and/
or lead to respiratory infections, cancer, birth defects or
other reproductive harm. The risk from inhaling dusts
depends on the exposition. Use dust extraction matched
appropriately for the developing dust, as well as personal
protective equipment and provide for good ventilation of
the workplace. Leave the processing of asbestos-contain-
ing materials to specialists.
Wood and light-metal dust, hot mixtures of sanding dust
and chemical materials can self-ignite under unfavourable
conditions or cause an explosion. Avoid sparking in the
direction of the dust collector as well as overheating of
the power tool and the materials being sanded, empty
the dust collector/container in time, observe the material
manufacturer's working instructions, as well as the rele-
vant regulations in your country for the materials being
worked.
Hand/arm vibrations
The vibration emission level given in this information
sheet has been measured in accordance with a standard-
ised test given in EN 60745 and may be used to compare
one tool with another. It may be used for a preliminary
assessment of exposure.
The declared vibration emission level represents the
main applications of the tool. However if the tool is used
for different applications, with different accessories or
poorly maintained, the vibration emission may differ.
This may significantly increase the exposure level over
the total working period.
An estimation of the level of exposure to vibration
should also take into account the times when the tool is
switched off or when it is running but not actually doing
the job. This may significantly reduce the exposure level
over the total working period.
Identify additional safety measures to protect the opera-
tor from the effects of vibration such as: maintain the tool
and the accessories, keep the hands warm, organisation
of work patterns.
The vibrational emission values are given for polishing
with lambskin and sanding with sanding sheet. Other
applications, such as polishing with other polishing acces-
sories than the lambskin can lead to other vibrational
emission values.
Operating instructions.
Press the locking button only when the motor is
stopped. (see page 5)
Putting into operation:
Note: The application tool begins to move
with short, low-power impulses. With
this, the polisher indicates the actuation of the first
switchpad.
Notes: The polisher does not start:
– when the switchpads on the sides and the pushbutton
on top are pressed at the same time
– if one or more of the pressing surfaces is/are pressed
while the mains plug is inserted
Note: The power tool starts with the lowest speed at each
starting procedure.
The speed can only be adjusted while the motor is run-
ning.
The self-start prevention lock prevents the power tool
from automatically restarting again, even after a brief
interruption of the power supply, e. g., from a pulled
mains plug. Switch the power tool off and then on again.
Repair and customer service.
When working metal under extreme operat-
ing conditions, it is possible for conductive
dust to settle in the interior of the power
tool. The total insulation of the power tool can be
impaired. Blow out the interior of the power tool via the
ventilation slots frequently with dry and oil-free com-
pressed air, and connect a residual current device (RCD)
on the line side.
If the supply cord of this power tool is damaged it must
be replaced by a specially prepared cord available
through the FEIN customer service centre.
The current spare parts list for this power tool can be
found in the Internet at www.fein.com.
If required, you can change the following parts yourself:
Application tools, auxiliary handle, safety guard, work
arbors, flanges.
Warranty and liability.
The warranty for the product is valid in accordance with
the legal regulations in the country where it is marketed.
In addition, FEIN also provides a guarantee in accordance
with the FEIN manufacturer's warranty declaration.
The delivery scope of your power tool may include only
a part of the accessories described or shown in this
instruction manual.
Declaration of conformity.
FEIN declares itself solely responsible for this product
conforming with the relevant provisions given on the last
page of this Instruction Manual.
Technical documents at: C. & E. FEIN GmbH,
C-DB_IA, D-73529 Schwäbisch Gmünd
Environmental protection, disposal.
Packaging, worn out power tools and accessories should
be sorted for environment-friendly recycling.
Selection of accessories (see page 9).
Use only original FEIN accessories. The accessories must
be intended for the power tool type.
Use accessories A–B with the safety guard mounted.
A
Backing pad for lambskin with tensioning cord
B
Backing pad with Velcro attachment for working
with polishing sponges, lambskin
Publicidad
