Electrical Connection; Ecodesign Regulation; Advice Regarding The First Wash Cycle; Technical Data - SCHOLTES LTE 14-H208A+ Instrucciones De Uso

Anti-flooding protection
EN
To ensure floods do not occur, the dishwasher:
- is provided with a special system which blocks the
water supply in the event of anomalies or leaks from
inside the appliance.
Some models are also equipped with the supplementary
safety device New Acqua Stop
flooding protection even in the event of a supply hose
rupture.
WARNING: HAZARDOUS VOLTAGE!
Under no circumstance should the water inlet hose be
cut as it contains live electrical parts.

Electrical connection

Before inserting the plug into the electrical socket, make
sure that:
• The socket is earthed and complies with current
regulations.
• The socket can withstand the maximum load of the
appliance, which is indicated on the data plate
located on the inside of the door ( see chapter entitled
Description of the appliance ).
• The power supply voltage falls within the values
indicated on the data plate on the inside of the door.
• The socket is compatible with the plug of the
appliance. If this is not the case, ask an authorised
technician to replace the plug ( see Assistance ); do
not use extension cables or multiple sockets.
Once the appliance has been installed, the power
supply cable and the electrical socket should be easily
accessible.
The cable should not be bent or compressed.
If the power supply cable is damaged, it must be re-
placed by the manufacturer or its Technical Assistance
Service in order to prevent all potential hazards. (See As-
sistance)
The Company shall not be held responsible for any
incidents that occur if these regulations are not
observed.

ECODESIGN REGULATION

ECO wash cycle is the standard cycle to which the energy label data refers; this cycle can be used to wash crockery with a normal
soil level and is the most efficient in terms of energy and water consumption for this type of crockery. To reduce consumption even
further, only run the dishwasher when it is full.
Standby consumption: Left-on mode consumption: 4,5 W – Off mode consumption: 1,3 W
Consumption data table for the main cycles
Standard conditions
Energy consumption
(kWh/cycle)
INTENSIVE 1,50
NORMAL 1,20
*
Cycle data refers to the values recorded in a laboratory, in accordance with European standard EN 50242.
**
Data is obtained by recording values when the appliance is operational and loaded with user crockery.
14
*
, which guarantees anti-
*
Water consumption Duration
(l/cycle) (min/cycle)
15 150
15 120
*
Anti-condensation strip
After installing the dishwasher, open the door and stick the
adhesive transparent strip under the wooden shelf in order
to protect it from any condensation which may form.

Advice regarding the first wash cycle

After the appliance has been installed, immediately before
running the first wash cycle, completely fill the salt
dispenser with water and add only then approximately 1 kg
of salt ( see chapter entitled Rinse aid and refined salt ). The
water may overflow: this is normal and is not a cause for
concern. Select the water hardness value ( see chapter
entitled Rinse aid and refined salt ). - After the salt has been
poured into the machine, the LOW SALT indicator light
switches off.
If the salt container is not filled, the water softener and
the heating element may be damaged as a result.

Technical data

width 59.5 cm
height 82 cm
Dimensions
depth 57 cm
Capacity 14 standard place-settings
Water supply 0,05 ÷ 1MPa (0.5 ÷ 10 bar)
pressure 7,25 – 145 psi
Power supply
See appliance data plate
voltage
Total absorbed
See appliance data plate
power
Fuse See appliance data plate
This dishwasher conforms to
the following European
Community Directives:
-2006/95/EC (Low Voltage)
-2004/108/EC (Electromagnetic
Compatibility)
-2005/32/EC (Comm. Reg.
1275/2008) (Ecodesign)
-97/17/EC (Labelling)
-2002/96/EC (WEEE)
**
User conditions
Energy consumption Water consumption
(kWh/cycle) (l/cycle)
1,30 14
1,05 14
*
Duration
(min/cycle)
135
110