General Safety Information - Campbell Hausfeld HG3007 Manual Del Usuario

Operating Instructions
General Safety
CALIFORNIA pROpOSITION 65
This product or its
power cord may
contain chemicals, including lead,
known to the State of California
to cause cancer and birth defects
or other reproductive harm. Wash
hands after handling.
You can
create
dust when you cut, sand,
drill or grind materials
such as wood, paint,
metal, concrete, cement, or other
masonry. This dust often contains
chemicals known to cause cancer,
birth defects, or other reproductive
harm. Wear protective gear.

GENERAL SAFETY INFORMATION

Air compressors are utilized in a variety
of air system applications. Because air
compressors and other components
(material pump, spray gun, filters,
lubrications, hoses, etc.) used make up
a high pressure pumping system, the
following safety precautions should be
observed at all times. Only persons well
acquainted with these rules of safe
operation should be allowed to use the
air compressor.
Risk of Bursting! This
compressor is designed
to provide air pressure
up to 200 psi. Most
attachments are designed to
operate at a maximum pressure
of less than 125 psi. DO NOT
adjust the regulator to result in
output pressure greater than the
marked maximum pressure of the
attachment.
Risk of Injury!
Do not direct air
stream at body.
All electrical work
should be done
by a qualified (licensed or certified)
electrician. On a properly wired
circuit, the black wires supply a
voltage potential even when the
unit is off.
1. Read instruction
manuals for each
component carefully,
before attempting to
assemble, disassemble
or operate your particular system.
www.chpower.com
2. Wear safety glasses and
use hearing protection
when operating the
pump or unit.
3. Do not stand on or use the pump or
unit as a handhold.
4. Do not exceed pressure rating of
any component in system.
5. Protect material lines and air lines
from damage or puncture. Keep
hose and power cable away from
sharp objects, chemical spills, oil,
solvents, and wet floors.
6. Never point a spray gun at oneself
or any other person. Accidental
discharge may result in serious
injury.
7. Check hoses for weak or worn
condition, before each use, making
certain all connections are secure;
do not use if deficiency is found.
Notify an authorized service facility
for examination or repair.
Leaving compressor in ON
position may allow it to turn on
inadvertently. To prevent this and
possible damage from power surge,
turn to OFF position after each use.
8. Release all pressures within system
slowly; dust and debris may be
harmful.
away from a running
compressor; fast moving
and hot parts will cause
injury and/or burns.
system before servicing air
compressor!
9. Follow all local electrical and safety
codes, as well as the National
Electrical Code (NEC) and the
Occupational Safety and Health Act
(OSHA).
10. Wiring and fuses should follow
electrical codes, current capacity,
and be properly grounded.
11. Electric motors must be securely
and adequately grounded. See
grounding instructions and
MANUAL
extension cord information, in this
manual.
12. Always disconnect power source
13. Guard all moving parts; keep visitors
14. Use only a properly grounded outlet
when touching exterior
of operating motor; it
may be hot enough to
cause injury. Compressor parts may
be hot even if the unit is stopped.
15. Protect power cable from coming in
16. Clean electrical or electronic
Do not run
unattended.
electrical equipment
and controls can cause
electrical arcs that will
ignite a flammable gas or vapor.
Never operate or repair the unit
near a flammable gas or vapor.
Keep
Never store flammable liquids
fingers
or gases in the vicinity of the
compressor.
17. To reduce fire hazard,
Disconnect power
and depressurize
18. To avoid spontaneous combustion,
19. NEVER reset safety valve or pressure
adjust safety valve. Keep safety
valve free from paint and other
accumulations.
20. Do regular maintenance; keep all
2
before working on or near a motor,
or its connected load. If power
disconnect point is out-of-sight, lock
it in the open position and tag to
prevent unexpected application of
power.
away. Never allow children in work
area.
that will accept a three pronged
plug, and wear shoes to prevent
shock hazards.
Be
careful
contact with sharp objects.
equipment with an approved
cleaning agent, such as dry,
nonflammable cleaning solvent.
Motors,
keep engine/motor
exterior free of oil,
solvent, or grease.
discard waste rags into approved
metal waste cans.
switch. Keep safety valve free from
paint and other accumulations.
This provides safety against over
pressure.
Never remove or
attempt to
nuts, bolts, and screws tight, to be
sure equipment is in safe working
condition .