Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!
INCLUDED WITH THIS FAN:
(1) 3 Speed, Oscillating Motor Assembly
(1) Column Assembly
(1) Base
(1) Blade
(1) Front Grill
(1) Rear Grill
(1) Hardware Bag
(1) Motor Hardware Bag
(1) Wheel Kit Bag
(1) Instruction Sheet
GENERAL SAFETY INFORMATION
1. Read all instructions before using Fan.
2. Make certain that the power source conforms to the electri-
cal requirements of the Fan.
3. Use this Fan only as described in this manual. Any other use not
recommended by the manufacturer may cause fire, electrical
shock, or injury to persons.
4. To reduce the risk of personal injury and electric shock, the
Fan should not be played with or placed where small children
can reach it.
5. Unplug power cord before servicing, or moving the Fan.
WARNING:
DO NOT DEPEND UPON THE ON-OFF SWITCH
AS THE SOLE MEANS OF DISCONNECTING POWER WHEN
INSTALLING OR SERVICING THE FAN. ALWAYS UNPLUG THE
POWER CORD.
6. This Fan must NOT be used in potentially dangerous
locations such as flammable, explosive, chemical-laden
or wet atmospheres.
7. DO NOT use Fan in or near a window. Rain may create an
electrical hazard.
8. Completely reassemble Fan, according to instructions,
before reconnecting to power supply.
9. The power cord is equipped with a three-prong grounded
plug that must be inserted into a matching receptacle. Under
no circumstances should the grounding prong be cut off the
plug. Where a two-prong wall receptacle is encountered,
it must be replaced with a properly grounded three-prong
receptacle installed in accordance with the National Electrical
Code (NEC) and all applicable local codes and ordinances.
This work must be done only by a qualified electrician, using
copper wire only.
WARNING:
USE OF A THREE-PRONG TO TWO-PRONG
ADAPTER IS NOT RECOMMENDED. IMPROPER CONNECTION
MAY CREATE THE RISK OF ELECTROCUTION. USE OF SUCH
ADAPTER IS NOT PERMITTED IN CANADA.
10. Where possible, avoid the use of extension cords. If they must
be used, minimize the risk of overheating by ensuring that they
are UL listed. Never use a single extension cord to operate
more than one Fan.
Rev. E 8/10
30" INDUSTRIAL GRADE OSCILLATING
READ AND SAVE THESE INSTRUCTIONS
RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
PEDESTAL FAN WITH WHEELS
Model 3138
11. NEVER operate any Fan with a damaged cord or plug or after
the Fan malfunctions, has been dropped or damaged in any
manner.
12. Do not insert or allow fingers or foreign objects to enter any
ventilation or exhaust opening as it may cause an electric shock
or fire, or damage the Fan. Do not block or tamper with the Fan
in any manner while it is in operation.
13.Always place the Fan on a stable, flat, level surface when
operating, to avoid the chance of the Fan overturning. Locate
the Power Cord so the Fan or other objects are not resting on it.
Do not run cord under carpeting. Do not cover cord with throw
rugs, runners, or similar coverings. Do not route cord under
furniture or appliances. Arrange cord away from traffic area and
where it will not be tripped over.
14.This Fan is not intended for use in wet or damp locations.
Never locate a Fan where it may fall into a bathtub or other
water container.
15. Do not use Fan outdoors.
16.This Fan is not suitable for use in agricultural facilities including
areas where livestock, poultry or other animals are confined.
Please refer to National Electric Code (NEC) Article 547-7
(2008), or applicable state or local codes or standards relating
to electrical requirements for Agricultural Buildings. THIS FAN
DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE
547-7 (2008).
17.This Fan is not suitable for use in hazardous locations. Please
refer to National Electric Code (NEC) Article 500 or applicable
state or local codes or standards relating to electrical
requirements for Hazardous locations. THIS FAN DOES NOT
MEET THE REQUIREMENTS OF NEC ARTICLE 500 (2008).
WARNING:
REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK
– DO NOT USE THIS FAN WITH ANY SOLID STATE SPEED
CONTROL DEVICES.
CAUTION:
BECAUSE OF THE SIZE AND WEIGHT OF THIS
FAN, MAKE SURE ALL PARTS ARE COMPLETELY ASSEMBLED
ACCORDING TO INSTRUCTIONS. FAILURE TO DO SO COULD
RESULT IN FAN COMING APART DURING OPERATION AND/OR
PERSONAL INJURY.
SAVE THESE INSTRUCTIONS
1
5084445
Publicidad
Tabla de contenido
Manuales relacionados para Lasko 3138
Resumen de contenidos para Lasko 3138
- Página 1 30" INDUSTRIAL GRADE OSCILLATING PEDESTAL FAN WITH WHEELS Model 3138 READ AND SAVE THESE INSTRUCTIONS READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE OR MAINTAIN THE PRODUCT DESCRIBED. PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN INSTRUCTIONS FOR FUTURE REFERENCE.
-
Página 2: Hardware Bag Contents
HARDWARE BAG CONTENTS HARDWARE BAG D: HARDWARE BAG A: (1) Left Wheel Assembly (1) Mounting Flange (1) Right Wheel Assembly (1) Square Head Bolt (3/8-16 X 1”) (4) Carriage Bolts (5/16-18 X 1”) (4) Carriage Bolts (3/8-16 X 1”) (4) Split Lockwashers (5/16”) (4) Split Lockwashers (3/8”) (4) Hex Nuts (3/8-16) (4) Hex Nuts (5/16-18) -
Página 3: Base Assembly
BASE ASSEMBLY Carriage Bolts (4) Locate Hardware Bag “A” to Assemble Base. (Figure 1) 1. Place Base on floor. 2. Fit Mounting Flange through large hole in center of Base. 3. Insert (4) 3/8-16 X 1” Carriage Bolts through Mounting Flange and Base. - Página 4 COLUMN AND MOTOR ASSEMBLY GRILL AND BLADE ASSEMBLY Locate remaining parts from Motor Hardware Bag to Assemble Locate Motor Hardware Bag to Assemble Column and Motor Assembly. Grills and Blade to the Motor. 1. Place flat section on Upper Tube of Column Assembly next to 1.
- Página 5 REPOSITIONING INSTRUCTIONS 1. Disconnect ALL POWER before repositioning Fan. Never move Fan while blade is in motion. 2. Make sure Fan Head is secured by tightening 1/2” Hex Bolt and adjustment knob to secure the head assembly. 3. Make sure that the oscillation knob in the motor is in the locked down position. 4.
-
Página 6: Customer Service
WHAT LASKO WILL DO: During the warranty period, Lasko will, at its sole option, repair or replace any part or parts that prove to be defective or replace the whole product with the same or comparable model. -
Página 7: Incluido Con El Ventilador
VENTILADOR OSCILANTE DE PEDESTAL DE 30” CON RUEDAS, PARA USO INDUSTRIAL Modelo 3138 LEA Y GUARDE ESTAS INSTRUCCIONES LEA CUIDADOSAMENTE LAS INSTRUCCIONES ANTES DE INTENTAR ARMAR, INSTALAR, USAR O DAR MANTENIMIENTO AL PRODUCTO DESCRITO. PROTÉJASE A SÍ MISMO Y A LOS DEMÁS CUMPLIENDO CON TODA LA INFORMACIÓN DE SEGURIDAD. EL NO SEGUIR LAS INSTRUCCIONES PODRÍA RESULTAR EN LESIONES PERSONALES Y/O DAÑOS A LA PROPIEDAD. -
Página 8: Bolsa De Tornillería A
CONTENIDO DE LA BOLSA DE HERRAJES BOLSA DE TORNILLERÍA A: BOLSA DE TORNILLERÍA D: (1) Brida de montaje (1) Conjunto de Rueda Izquierda (1) Perno de cabeza cuadrada (3/8-16 x 1 pulg) (1) Conjunto de Rueda Derecha (4) Pernos de carruaje (3/8-16 x 1 pulg) (4) Perno de Carruaje (5/16-18 x 1 pulg) (4) Arandelas de seguridad divididas (3/8 pulg) (4) Arandela de Seguridad Dividida (5/16 pulg) -
Página 9: Montaje De La Base
MONTAJE DE LA BASE Tornillo De Carruaje (4) Ubique la Bolsa de Herrajes “A” para Montar la Base. (Figura 1) 1. Coloque la Base sobre el piso. 2. Encaje el Patín de Montaje a través del orificio grande en el centro de la Base. Tornillo De Cabeza 3. -
Página 10: Montaje De Columna Y Motor
MONTAJE DE COLUMNA Y MOTOR MONTAJE DE ENREJADO Y HÉLICE Ubique la Motor de bolsa tornillería para Montar el Conjunto de Ubique las partes restantes de la Motor de bolsa tornillería para Columna y Motor. Montar los Enrejados y la Hélice en el Motor. 1. -
Página 11: Mantenimiento
INSTRUCCIONES DE USO INSTRUCCIONES PARA EL REPOSICIONAMIENTO 1. Desconecte TODA LA ALIMENTACIÓN ELÉCTRICA. Nunca traslade el ventilador con la hélice en movimiento. 2. Asegúrese que el cabezal del ventilador esté bien sujeto apretando el perno hexagonal de 1/2 y la perilla de ajuste para fijar el conjunto del cabezal. -
Página 12: Servicio Al Cliente
Esta garantía no cubre los costos de envío para la devolución de productos a Lasko para su reparación o reemplazo. Lasko abonará los cargos de envío de devolución a Lasko con posterioridad a las reparaciones o el reemplazo bajo garantía.