Publicidad
Idiomas disponibles
Idiomas disponibles
continued
CD Player
The disc tray does not close.
The CD is not placed correctly.
The CD will not play.
The CD is dirty.
The CD is inserted label side down.
The player is in pause mode.
Moisture condensation has builtup.
Leave the system turned on for
about an hour until the moisture
evaporates.
Play does not start from the first
track.
The CD player is in programme or
shuffle mode. Press PLAY MODE
repeatedly so that "PROGRAM" or
"SHUFFLE" disappears.
"
" is displayed.
) on the unit was repeatedly
pressed at the end of the CD. Turn
the jog dial counterclockwise (or
GB
press = on the remote) to return
to the normal display.
22
General
There is no sound.
Press VOLUME +.
The headphones are connected.
Disconnect them.
Sound comes from one channel or
unbalanced left and right volume.
Check the speaker connections of
the inoperative channel.
The left and right sound are
reversed.
Check the speaker connection and
speaker placement.
Bass is lacking or the location of the
musical instruments is apparently
imprecise.
Check the speaker connection for
proper phasing.
There is severe hum or noise.
TV or VCR is too close to the stereo
system. Move the stereo system
away from the TV or VCR.
"0: 0 0" flashes in the display.
A power interruption occured.
Set the clock and timer settings
again.
For Your Information
The remote does not function.
The batteries have run down.
Replace both batteries.
There is an obstacle between the
remote and the system. Remove the
obstacle.
Restoring the Factory
Settings
Unplug the mains lead and then plug it
back into the wall outlet.
Keep DISPLAY and FUNCTION pressed
and press TAPE.
Maintenance
To clean the tape heads and tape
path
Contaminated tape heads cause poor
recording or sound drop-out in playback.
We recommend cleaning after every 10
hours of operation.
Open the tape compartment and wipe the
heads, the pinch rollers and the capstans
with a cleaning swab slightly moistened
with cleaning fluid or alcohol. Wipe the
parts shown below.
Deck A
Cleaning swab
Playback head
Deck B
Cleaning swab
Erase head
Record/playback head
Insert a tape when the areas cleaned are
completely dry.
To demagnetize the tape heads
After 20 to 30 hours of use, enough residual
magnetism will have built up on the heads
to begin to cause loss of high frequencies
and hiss. At this time, demagnetize the
heads and all metal parts in the tape path
with a commercially available tape head
demagnetizer. Refer to the instructions of
the demagnetizer.
To clean the cabinet
Use a soft cloth slightly moistened with
mild detergent solution.
To clean the CD
When a CD is dirty, clean it with a cleaning
cloth. Wipe the CD from the centre out.
Notes on CD
•Do not use solvents such as benzene,
thinner, commercially available cleaners,
or anti-static spray intended for vinyl LPs.
•If there is a scratch, dirt or fingerprints on
the CD, it may cause a tracking error.
Specifications
CD player section
System
Laser
Laser output
Capstan
Wavelength
Pinch roller
Frequency response
Signal-to-noise ratio
Dynamic range
Capstan
Tuner section
FM stereo, FM/AM superheterodyne tuner
FM tuner section
Tuning range
Pinch roller
Aerial
Aerial terminals
Intermediate frequency
Compact disc digital audio
system
Semiconductor laser (λ =
780 nm)
Emission duration:
continuous
Max 44.6 µW*
* This output is the value
measured at a distance of
200 mm from the
objective lens surface on
the Optical Pick-up Block
with 7 mm aperture.
780 – 790 nm
2 Hz – 20 kHz
More than 65 dB
More than 97 dB
87.5 – 108.0 MHz (50 kHz
step)
FM lead aerial
75 ohm unbalanced
10.7 MHz
Publicidad
