Troubleshooting - Pulsar FORWARD F455 Instrucciones De Uso

Using the Weaver Rail
The device is equipped with a Weaver rail (15) which allows the user to mount extra accessories. You must first
detach the removeable IR illuminator (See Section "IR Illuminator").
Display Calibration
The attachment is configured so that after fitting onto an optical sight that had been properly zeroed, no
adjustment of the aiming point is required. If your attachment has been subjected to a sharp blow, or has been
dropped, you may check the impact point and correct it yourself if required, without having to take it to the
service centre.
•
To enter display calibration mode, first press and hold the M
button (7) for 10 seconds.
•
The display coordinates X=0; Y=0 will appear.
•
Use the LEFT (8) and RIGHT (6) buttons to move the display
horizontally (X axis) and vertically (Y axis) so that the point of
impact moves to the centre of the aiming mark of your optical
sight.
• Press the M button (7) to toggle between the X and Y
coordinates.
•
The image offset is 1 sensor pixel.
•
The image offset range is +/- 20 pixels horizontally (X axis),
+/- 20 pixels vertically (Y axis).
•
To exit the menu and save the settings, press and hold the M button (7) for two seconds.
Stream Vision
Forward attachments support Stream Vision technology, which allows you to stream an image from the thermal
imager to your smartphone or tablet PC via Wi-Fi in real time mode.
You can find detailed instructions on the operation of Stream Vision technology online at www.pulsar-vision.com.
Note: the device's design includes the possibility of firmware updates. Updating is possible via the Stream
Vision app. Scan or press on a QR code to download the application:
Technical Inspection
A check is recommended before each use of the device.
Check:
•
External appearance (there should be no cracks on the housing).
•
The condition of the lens and eyepiece the digital module and the lens of the IR illuminator (there should be
no cracks, grease spots, dirt or other residue). Wipe the exterior surfaces of metal and plastic parts free from
dust, dirt and moisture with a soft, cotton cloth.
•
The state of the Battery Pack (should be charged) and the electric terminals (there should be no sign of salts
or oxidation).
•
The controls should be in working order.
•
The digital module should be properly and firmly attached to the optical device.
Display coordinates Impact point
Optical sight reticle Display displacement
Technical Maintenance
Technical maintenance should be carried out at least twice a year and include the following steps:
•
Wipe the external surfaces of metal and plastic parts free of dust and dirt with a cotton cloth. Silicone grease
may be used for this.
•
Clean the electric terminals of the Battery Pack and battery slot on the device using a non-greasy organic solvent.
•
Check the glass surfaces of the eyepiece and the lens. If necessary, remove dust and sand from the lenses
(preferably using a non-contact method). Cleaning of the external surfaces of the optics should be done with
substances designed especially for this purpose.
Storage
Always store the device in its carrying case, in a dry, well-ventilated space. It is essential during prolonged
storage to remove the Battery Pack.

Troubleshooting

Malfunction Possible reason
The device will not power Battery Pack is completely
on. discharged.
Does not operate from USB cable damaged.
external power source.
External power source discharged.
Smartphone or tablet Device password has been changed. Delete the network and reconnect using the
cannot be connected to the
device.
The device is in an area with a large
number of Wi-Fi networks that may
cause interference.
Wi-Fi signal non-existent or Device is outside the area of Wi-Fi
interrupted. coverage. There are obstacles
between the device and the
receiver (e.g. concrete walls).
Poor image quality. These problems may occur during observation in difficult weather conditions
(snow, rain, fog etc.).
Image is too dark. Low brightness or contrast level set. Adjust brightness or contrast.
Coloured lines appear The device was exposed to static
on display or image has electricity during operation.
disappeared.
There is a clear image of Dust or condensation on the
the aiming mark, but a interior or exterior optical surfaces
fuzzy image of the object. of the lens.
The lens will not focus.
The display is not centred. Position of the attachment on the
day sight requires adjusting.
Correction
Charge the battery.
Replace USB cable.
Charge the external power source.
device password.
To ensure stable Wi-Fi operation, relocate
the device to an area with fewer Wi-Fi
networks, or into an area with none.
Relocate the device into direct line of sight
of the Wi-Fi signal.
After exposure to static electricity, the
device may either reboot automatically, or
require turning off and on again.
Wipe the exterior optical surfaces with a
soft cotton cloth. Dry it. Let it stand for 4
hours in a warm room.
Adjust the sharpness by rotating the lens
adjuster.
Remove the attachment and set the display
to the centre of the field of vision (see
section "Operation").
10