Remote Control Unit - Denon AVR-2802 Instrucciones De Operación

8

REMOTE CONTROL UNIT

• The included remote control unit (RC-904) can be used to operate not only the AVR-2802 but other remote
control compatible DENON components as well. In addition, the memory contains the control signals for
other remote control units, so it can be used to operate non-Denon remote control compatible products.
Inserting the batteries
q Remove the remote control unit's rear
cover.
w Set three R6P/AA batteries in the battery
compartment in the indicated direction.
e Put the rear cover back on.
Using the remote control unit
B
30°
30°
Approx. 7 m
Notes on Batteries
• Use R6P/AA batteries in the remote control unit.
• The batteries should be replaced with new ones
approximately once a year, though this depends on the
frequency of usage.
• Even if less than a year has passed, replace the batteries
with new ones if the set does not operate even when the
remote control unit is operated nearby the set. (The
included battery is only for verifying operation. Replace it
with a new battery as soon as possible.)
• When inserting the batteries, be sure to do so in the
proper direction, following the "≈" and "√" marks in the
battery compartment.
• To prevent damage or leakage of battery fluid:
• Do not use a new battery together with an old one.
• Do not use two different types of batteries.
• Do not short-circuit, disassemble, heat or dispose of
batteries in flames.
• Remove the batteries from the remote control unit when
you do not plan to use it for an extended period of time.
• If the battery fluid should leak, carefully wipe the fluid off
the inside of the battery compartment and insert new
batteries.
• When replacing the batteries, have the new batteries
ready and insert them as quickly as possible.
• The learned remote control signals may be cleared if no
batteries are in the remote control unit for about 5
seconds.
The factory-installed codes are in permanent memory,
however.
• Point the remote control unit at the remote sensor on the
main unit as shown on the diagram.
• The remote control unit can be used from a straight
distance of approximately 7 meters from the main unit,
but this distance will be shorter if there are obstacles in
the way or if the remote control unit is not pointed directly
at the remote sensor.
• The remote control unit can be operated at a horizontal
angle of up to 30 degrees with respect to the remote
sensor.
NOTES:
• It may be difficult to operate the remote control unit if the
remote sensor is exposed to direct sunlight or strong
artificial light.
• Do not press buttons on the main unit and remote control
unit simultaneously. Doing so may result in malfunction.
• Neon signs or other devices emitting pulse-type noise
nearby may result in malfunction, so keep the set as far
away from such devices as possible.
Operating DENON audio components
• Turn on the power of the different components before operating them.
1
Set mode switch 1 to "AUDIO (AVR/AVC)".
AUDIO
AVR/AVC VIDEO
2
Set mode switch 2 to the position for the
TAPE CDR/MD
CD MULTI
component to be operated.
DVD TV
VDP VCR
3
Operate the audio component.
• For details, refer to the component's operating instructions.
While this remote control is compatible with a wide range of infrared controlled components, some
models of components may not be operated with this remote control.
1. CD player (CD) and CD recorder and
MD recorder (CDR/MD) system buttons
VCR-2/V.AUX
TV/VCR
+10
A / B
VOLUME DISC SKIP+
6, 7 : Manual search (forward and reverse)
2 : Stop
1 : Play
8, 9 : Auto search (cue)
3 : Pause
DISC : Switch disc
SKIP + (for CD changers only)
3. Tuner system buttons
SYSTEM CALL POWER
SET CALL OFF ON / SOURCE
DVD VDP TUNER SHIFT
1 2 3
TV/DBS PHONO
4 5 6
VCR-1 CD CDR / TAPE CHANNEL
7 8 9
SHIFT : Switch preset channel range
CHANNEL : Preset channel up/down
+, –
ENGLISH
RC-904
START LEARNED/TX
SYSTEM CALL POWER
SET CALL OFF ON / SOURCE
DVD VDP TUNER SHIFT
1 2 3
TV/DBS PHONO
4 5 6
VCR-1 CD CDR / TAPE CHANNEL
7 8 9
VCR-2/V.AUX
TV/VCR
+10 0
A / B
3
VOLUME DISC SKIP+
DOLBY / DTS
SPEAKER SURROUND DIRECT
DSP SIMULATION 5CH / 6CH STEREO STEREO
MASTER VOL.
INPUT MODE ANALOG EXT.IN
TAPE CDR/MD
1 AUDIO CD MULTI MUTING
2
AVR/AVC VIDEO DVD TV
VDP VCR
SYSTEM SURROUND
TUNING SETUP PARAMETER
TITLE MENU/GUIDE
BAND RDS
CH SELECT
3
ENTER
MODE PTY
SELECT
MEMORY RT STATUS ON SCREEN
DISPLAY RETURN
USE/LEARN T.TONE MULTI DVD
SET UP
2. Tape deck (TAPE) system buttons
VCR-2/V.AUX
TV/VCR
+10
A / B
VOLUME DISC SKIP+
6 : Rewind
7 : Fast-forward
2 : Stop
1 : Forward play
3 : Pause
8 : Reverse play
A/B : Switch between decks A and B
* For the tuner only, the following buttons can also be
operated:
SYSTEM SURROUND
TUNING SETUP PARAMETER
TITLE MENU/GUIDE
BAND RDS
CH SELECT
ENTER
MODE PTY
SELECT
MEMORY RT STATUS ON SCREEN
DISPLAY RETURN
TUNING •, ª : Tuning up/down
BAND : Switch between AM and FM bands
MODE : Switch between auto and mono
MEMORY : Preset memory
SHIFT : Switch preset channel range
RDS : RDS search
PTY : PTY search
RT : Radio text
15