Troubleshooting Guide & Pump Disassembly & Storage - Polygroup SUMMER WAVES Manual De Usuario

WARNING:
TURN OFF THE PUMP AND UNPLUG THE POWER CORD BEFORE TROUBLESHOOTING THE FILTER PUMP.
PROBLEM
A Unit not plugged in or
1 Motor fails to
start or kicks
on and off B GFCI Plug and/or circuit
C Low voltage
A Low pool water level
No or slow
2
water flow
B Inlet/Outlet clogged
through the
return fitting.
C Dirty filter cartridge
A Chlorine level
3 Filter pump is
not cleaning
B pH level
the pool
properly(Cloudy
water,
C Dirty filter cartridge
green.....etc.)
D Damaged filter cartridge
E Slow water flow
F Other chemicals required
G Pool water very dirty
A Suction/Return hose
4 Water leakage
B Vent screw in Seal Top
C Seal Top
POOL PUMP DISASSEMBLY & STORAGE
1. Turn off and Unplug the Power Filter Pump Remove the RF Diverter
Now, hand tighten the SF Cap
2. Slowly unscrew the V e nt Screw
2 1
3. Remove the Seal T o p 18 by turning counter-clockwise.
4 1
4. Remove the Filter Cartridge
21
Loosen all four Hose Clamps 14
6. Clean and dry all of the filter pump parts including filter cartridges.
7.
Liberally lubricate the Canister Gasket
parts of the Filter Pump Assembly
8. All items should be stored in a dry environment that remains above 32 degrees Fahrenheit at all times.
Should you encounter any problems, contact Customer Service at (888) 919-0070 from 8 AM to 5 PM Mon. thru Fri.
TROUBLESHOOTING GUIDE
CAUSE
A Unit must be plugged into a grounded 3-prong power outlet. Press the reset button on the
GFCI not activated
B Reset the GFCI plug and/or circuit breaker. If problem persists, have the circuit
breaker tripped
C Check the line voltage, it must be in the range of 105 to 125 Volts A.C.
A Fill the pool to the fill line. The suction fitting must be at least 4" under water.
B Check for obstructions(s) at the suction fitting and return fitting.
C Clean or replace the filter cartridge. A spare cartridge makes service more convenient.
A Maintain chlorine level between 1.0 to 1.6 ppm.
B Maintain pH level between 7.3 to 7.8.
C Clean or replace the filter cartridge. A spare cartridge makes service more convenient.
D Inspect the filter cartridge for holes or tears. If visibly damaged; replace the filter cartridge
E Check for obstructions(s) at the suction fitting and return fitting.
F Have the pool water sample tested by a pool supply store. It may be necessary to add other
G Chemicals are required to maintain clean pool water. Clean pool and filter more often.
A Tighten the hose clamps. Check the o-rings on the suction/return fittings.
B Check if O-ring
C Check Canister Gasket
5 onto the Suction Fitting 2 .
2
16 from the Seal T op 1 18 allowing the Filter Pump to depressurize.
and remove any chlorine tablets left inside the core section of the filter.
, remove the Hoses 13 and allow the water to drain out.
19 at the Seal Top 18
15 . Store all filter parts carefully.
MST. Extended operating days and hours during peak season requirements.
GFCI to start the pump.
checked by a qualified electrician.
chemicals due to varying water quality in different localities.
Check hoses for damage. Replace if needed.
is damaged. Replace if needed.
17
19 for damage. Replace if needed.
19
7 from the Return Fitting 6
and the O-Ring 17 on the Vent Screw
OWNER'S MANUAL
SOLUTION
and then plug the Return Fitting 6
16 with petroleum jelly, and then reassemble all of the
with the RF Plug 23 .
13