Fcc Rules And Regulations - Gemini VH Serie Manual Del Propietário

INTRODUCTION
Congratulations on purchasing a Gemini wireless system. This state of the art unit includes the latest features
backed by a three year limited warranty. Prior to use, we suggest that you carefully read all the instructions. This
book includes instructions for both the VH-101 and the VH-120 systems.
CAUTIONS
1. All operating instructions should be read before using this equipment.
2. To reduce the risk of electrical shock, do not open the unit. There are NO USER REPLACEABLE PARTS
INSIDE. Please refer servicing to a qualified service technician.
3. Do not expose this unit to direct sunlight or to a heat source such as a radiator or stove.
4. Dust, dirt and debris can interfere with the performance of this unit. Make an effort to keep the unit away from
dusty, dirty environments, and cover the unit when it is not in use. Dust it regularly with a soft, clean brush.
5. When moving this equipment, it should be placed in its original carton and packaging. This will reduce the
risk of damage during transit.
6. DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE.
7. DO NOT USE ANY SPRAY CLEANER OR LUBRICANT ON ANY CONTROLS OR SWITCHES.

FCC RULES AND REGULATIONS

Gemini wireless systems are the type accepted under FCC rules parts 74 and 15. Licensing of Gemini equipment
is the user's responsibility and licensability depends on the user's classification and application.
NOTE
This equipment has been tested and found to comply with the limits set forth under part 15 and 74 of FCC rules.
This equipment operates at a frequency that has been authorized by the FCC. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause interference to radio or
television reception, try one or more of the following suggestions:
1. Repoint or relocate the receiving antenna.
2. Plug the equipment into a socket on a different circuit.
3. Call your dealer to arrange to exchange the unit for one with a different frequency.
Remember, any changes made to the unit without authorization from Gemini will void your warranty.
VH-101 SINGLE CHANNEL WIRELESS SYSTEM
The VH-101 single channel VH series wireless system is a high quality audio product that provides excellent
performance under most operating conditions.
Four different models are available and all operate on a VHF high band frequency between 174.60 MHZ to
204.60 MHZ.
THE MODELS AVAILABLE ARE:
VH-101M - which comes equipped with a hand held microphone transmitter.
VH-101L - which comes equipped with a belt pack and lavalier transmitter.
VH-101H - which comes equipped with a belt pack and a headset transmitter.
ALL MODELS ARE AVAILABLE IN SIX DIFFERENT FREQUENCIES:
Frequency Conversion Chart:
Channel Frequency
1 174.60 MHZ
2 177.60 MHZ
3 180.60 MHZ
4 186.60 MHZ
5 192.60 MHZ
6 198.60 MHZ
7 201.60 MHZ
8 204.60 MHZ
VH-101 SINGLE CHANNEL RECEIVER OPERATION
Note: Effective range between the transmitter and receiver is up to 150 feet.
1. Remove all packing materials. Save the box and packing material to transport the unit, and in case the unit
ever requires service.
2. Plug the AC adaptor into the rear of the receiver where the jack is labeled DC 12V. Then plug the adaptor into
an appropriate AC outlet. Switch the power to the ON position. Note: The adaptor is available in 120V AC or
230V AC.
3. Extend the antenna fully vertical and point it toward the direction you will be speaking from.
4. Insert the 1/4" phone cable into the jack labeled AUDIO OUT on the rear of the receiver, and connect the
other end of the cable to your amp, effects or mixer mic jack.
5. Adjust the volume using the level control on the front panel.
PAGE 1
6. To adjust the squelch, place the small plastic tool (included with the unit) in the hole marked SQUELCH at the
back of the unit, and slowly turn the tool to adjust the output level to just above the level of background noise.
Setting the squelch too high will reduce the range of the system. Setting the squelch too low will increase the
level of unwanted noise.
VH-120 DUAL CHANNEL WIRELESS SYSTEM
The VH-120 dual channel VH series wireless system is two separate single channel transmitters of different
frequencies transmitting to one unit that houses both frequency receivers. One output carries both frequency
signals to your mixer simultaneously through one cable.
Four different models are available and all operate on a VHF high band frequency between 174.60 MHZ to
204.60 MHZ.
THE MODELS AVAILABLE ARE:
VH-120M - which comes equipped with two hand held microphone transmitters.
VH-120L - which comes equipped with two belt packs and two lavalier transmitters.
VH-120H - which comes equipped with two belt packs and two headset transmitters.
ALL MODELS ARE AVAILABLE IN THREE SETS OF DIFFERENT FREQUENCIES:
Frequency Conversion Chart:
System Channels
1 1 & 5 174.60 MHZ/192.60 MHZ
2 2 & 6 177.60 MHZ/198.60 MHZ
3 3 & 7 180.60 MHZ/201.60 MHZ
4 4 & 8 186.60 MHZ/204.60 MHZ
VH-120 DUAL CHANNEL RECEIVER OPERATION
Note: Effective range between the transmitter and receiver is up to 150 feet each side.
1. Remove all packing materials. Save the box and packing material to transport the unit, and in case the unit
ever requires service.
2. Plug the AC adaptor into the rear of the receiver where the jack is labeled DC 12V. Then plug the adaptor into
an appropriate AC outlet. Switch the power to the ON position. Note: The adaptor is available in 120V AC or
230V AC.
3. Extend the antennas fully vertical and point them toward the direction you will be speaking from.
4. Insert the 1/4" phone cable into the jack labeled AUDIO OUT on the rear of the receiver, and connect the
other end of the cable to your amp, effects or mixer mic jack.
5. Adjust the volume using the level controls on the front panel.
6. To adjust the squelch, place the small plastic tool (included with the unit) in the hole marked SQUELCH at the
back of the unit, and slowly turn the tool to adjust the output level to just above the level of background noise.
Setting the squelch too high will reduce the range of the system. Setting the squelch too low will increase the
level of unwanted noise.
HAND HELD TRANSMITTER FEATURES
• High sensitivity cardiod capsule for professional use
• Special noise absorption parts inside the barrels eliminating switch shock and handling noise
• Frequency with quartz locked control
CAUTIONS
1. Do not drop the microphone onto a hard surface.
2. Do not strike the microphone head front with fist or fingers, and do not blow strongly into the microphone head
front.
3. Do not use the microphone in areas of high humidity and/or high temperature as this could lead to damage of
the microphone.
HAND HELD TRANSMITTER OPERATION
1. Open the battery holder by turning it counterclockwise. Insert a 9V battery into the battery holder according to
the polarity indication marked on the battery housing. Close the battery holder.
2. Push the power switch to the ON position. The BATT indicator should flash once briefly as you turn on the mic
indicating that the mic has sufficient power. If the BATT stays on, it indicates that the battery has insufficient
power and should be changed. If the BATT does not light at all and the mic does not work, it indicates that the
battery is dead , and you should change the battery. If the microphone is not going to be used for any length of
time, push the power switch to OFF and remove the battery. Do not switch the mic on and off rapidly, because
you won't get a true indication from the BATT indicator.
Frequencies
PAGE 2