Volume Control - Emtec EKCOH180 Manual Del Usuario

6) Automatic code search
When searching an unknown code, you can step through the library
automatically (AutoSearch). When your equipment responds, you can
stop the searching process and store the code you found.
Note: As you can dedicate any appliance (TV, DVD, SAT...) to the
VCR, DVD or SAT keys, you need first to enter any 4 digit code for
the kind of appliance you wish to control (found in the code book, i.e.:
If you want to program a SAT under the VCR key, enter any SAT code
found in the code book and then follow the steps below:
1. Turn on the device you want to control.
2. Press and hold SETUP (4) until the LED indicator (1) lights steadily. Release
SETUP button.
3. Press the mode key (3) that matches the equipment you want to control (for
example TV). Press first the Mode key (6) for DVBT, CBL, AMP and AUX
4. Press PROG+ (7) once. After a few seconds the remote starts stepping through
the code library (fast search, 1 code per second). When the device responds, you
can press PROG+ (7) to switch to slow search (1 code per 3 seconds). You can
step back by pressing PROG- (7) (you can step forward by pressing PROG+ (7) in
case you went too far back). As soon as the device responds again, press the -ENT
key (15) to store the code you found.
7) Brand search
If your brand is listed hereafter, you have the possibility to use the
brand search method (faster than the «manual» and the «automatic
code search»):
BRAND CODE
Philips/Radiola
Sony/Panasonic/JVC/Sharp Akai/Toshiba/Daewoo
Thomson/Brandt
Telefunken/Saba/Normende
Grundig/Blaupunkt
Nokia/ ITT
1. Turn on the device you want to control.
2. Press and hold SETUP (4) until the LED indicator (1) lights steadily. Release
SETUP button.
3. Press and release the mode key (3) of the device you want to control (for
example TV). Press first the Mode (6) key for DVBT, CBL, AMP and AUX.
4. Enter the code corresponding to your brand, point the 8 in 1 Universal Remote
Control in the direction of your equipment, press once only PROG+ (7) continue
to point the 8 in 1 Universal Remote Control at your equipment until the equip-
ment changes channel. (The remote control sends an IR signal every second. So
please wait until your equipment reacts). When your equipment does react, press
on the key ENT (15) to confirm. If accidentally you miss the code, you can stop
the autosearch by pressing PROG – (7) and by repeatedly pressing this key return
to the right code. Press ENT (15) to confirm.
8) Identifying codes found using the search procedure
1. Press and hold SETUP (4) until the LED indicator (1) lights steadily. Release
SETUP.
2. Press the mode key (4) for the equipment you want to identify (TV, VCR,
DVD or SAT). The LED blinks once. Note: press and release Mode key for
DVBT, CBL, AMP and AUX programing.
3. Press again SETUP. The LED blinks once.
4. To identify the first digit press each number button from 0 – 9 (13) until the
LED blinks. The number you pressed is the first digit of the code.
5. Press each number key from 0 – 9 as above to find the second and third digit.
7. Press each number key from 0 – 9 as above to find the fourth digit. When the
fourth digit has been found the LED will go off. Don't forget to write down the
code on the label of the battery compartment

9) Volume Control

Adjustment of ALL volume controls under a specific mode
You can program the remote control so that the volume and mute keys
control a specific device (the volume control must exist on the corres-
ponding device). E.g. control of TV sound in TV mode, VCR mode,
DVBT mode or SAT mode.
1. Press and hold SETUP (4) until the LED indicator (1) lights steadily. Release
SETUP.
2. Press and hold MUTE (10) until the LED (1) blinks once. Release MUTE.
3. Press once on the mode key (TV, SAT, ...) corresponding to the device whose
volume will always be controlled by the VOL (8) and MUTE (10) keys.
4. Press the MUTE (10) key once
Adjustment of the volume controls for EACH mode.
You can program the remote control so that the volume control is
functional for each mode selected (the volume control must exist on
the corresponding device). E.g. control of the television set sound in
TV mode, control of the SAT receiver sound in SAT mode,...
GB
.
.
1
2
3
4
5
6