Toto Clean Dry HDR110 SS Serie Manual De Instalación

0GU3049E
INSTALLATION MANUAL
Warranty Registration and Inquiry
For product warranty registration, TOTO U.S.A. Inc. recommends online Warranty Registration. Please visit our web site http://www.totousa.com. If you have questions regarding warranty policy
or coverage, please contact TOTO U.S.A. Inc., Customer Service Department, 1155 Southern Road, Morrow, GA 30260 (888) 295 8134 or (678)466-1300 when calling from outside of U.S.A.
Important Safeguards
(For your safety, please follow the instructions below.)
In this Installation Manual, the following symbols are shown for safe and proper use of
the product and to alert you of the possibility of personal injury and damage to your
property.
The symbols and their meanings are as follows:
Ignoring these symbols may cause
Warning
personal injury and/or property damage.
Ignoring these symbols may cause
Caution
severe injury and/or property damage.
*Some models may have different components from the ones illustrated below.
Warning
Do not install the unit in the places where corrosive
or combustible gas can be present.
This may cause product failure or damage.
Do not use this unit as hair dryer or for drying any objects
Do not other than hands.
This may cause electric shock, fire, injury or failure.
Never attempt to disassemble for repair or
modification.
This may cause electric shock, fire, injury or failure
Do not
disassemble
Do not install outdoors or where it is exposed to water.
This may cause current leakage, electric shock, fire, or failure.
Do not use in
humid area
Do not use this unit without filter or filter case.
This may cause electric shock, fire, injury or failure.
Do not
It is necessary to install a circuit-breaker in the power
supply.
Failure to do this may cause electric shock during overload or shortcircuit.
Important
Before Installing
1. Precautions
Confirm the rough-in, major dimensions and wiring diagram before installation
in order to properly install the hand dryer and electrical wiring.
All electrical wiring should be installed in accordance with national/local codes
and regulations with assistance from a certified electrician.
Mounting surface should be even and smooth.
Confirmation must be made that the wall has enough strength for hand dryer
installation and be sure to use all the mounting hardware provided to securely
install the hand dryer.
It is necessary to install circuit breaker for the power supply.
It is necessary to connect ground cable to ground terminal.
2. Others
Pay special attention so that both the top cover and the sensor surface are
not flawed or scratched.
Do not place other devices using inverter or infrared sensor near the
hand dryer, this may cause malfunction.
Recommended mounting bracket heights from floor are as follow:
*
- Male/Female: 29-1/2" (750 mm)
- Children: 23-1/2" (598 mm)
- Handicapped: 21-1/2" (547 mm)
Meets the American Disabilities Act Guidelines, ANSI A117.1 and CSA B651 requirements
when mounted in a recessed wall where the front surface is not more than 4" (102mm) from
finished wall and max. height of air blower outlet from finished floor is 47-1/4" (1200mm).
Clean Dry™
High Speed Concealed Hand Dryer
Warning
It is necessary to connect ground cable to ground
terminal.
Ground
Failure to do this may cause electric shock during overload or short circuit.
connection
Caution
The chassis assembly must be installed on a smooth
and even wall surface which has enough strength.
Important Failure to do this may cause damage or personal injury if it falls down.
Specification
Product HDR110#SS
Power Rating 120V AC, 4.25 Amps, 60 Hz, 510 W
Power Connection Hardwiring
Power Saving Function Automatically turns OFF after 60 seconds of use
Decibel Rating
58 dB(A)
Air Speed
224 mph (100 meters/second)
Dry Time
12 seconds
Drain Tray Capacity
0.27 gal (950 ml)
Ambient temperature 32° - 104°F (0° - 40°C)
Size 12-5/8" x 28-3/4" x 6-7/16"
22.2 lbs (10kg)
Weight
Set-up Drawing
Some models may have different components as illustrated below.
3-9/16" (90mm)
1-9/16" (40mm) 2-3/8" (60mm)
5-1/8"
2-3/8" (60mm)
(130mm)
11-5/8"
1-5/16"
(294mm)
(34mm)
FINISHED
WALL
1-9/16"
(40mm)
Junction box
(Actual Placement)
Power cable
26-5/16"
(668mm)
1-3/16" (30mm)
2" (50mm)
2-3/4" (70mm)
2-3/4" (70mm)
3-1/8" (80mm)
2"(50mm)
28-3/4"
(730mm)
OPEN WALL
2"
(50mm)
12-5/8" (320mm)
1-9/16" *
(40mm) 5-1/8"
(130mm)
FLOOR
6-7/16"
(164mm)
※ 5-5/16" (135mm) Min. space in wall.
2015.11
Installation
Hand Dryer Unit
Top cover
Color : White,Black,Green
Size : AWG16×3
Power Cable
Wiring Hole
Chassis Assy
Filter
Filter case
Accessories
Mounting Bracket Screws and Vandal Resist Hex Wrench
Bracket (Top)
Installation Installation Installation
position position position
Bracket (Bottom)
Installation Procedure
1
Using template provided, mark the wall for locations and install
the mounting bracket.
2
Remove Water Tray.
1-9/16"
(40mm)
Wall thickness needs
to be 5 to 30mm.
Beam/Stud
Bracket
(Top)
Water tray
Remove water tray
during installation
3
Complete the electrical wiring; install the junction box, and
connect the power cord using wire nuts.
4
Mount the chassis assembly and drain tray assembly.
5
Install the top cover and drain tray.
*Some models may have different component as illustrated below.
<Bottom view>
Air nozzles
Sensor
Wall surface
Filter case
Water Tray
※Model is subject to change without further notification.
Manual
(M4×6) ×2
(φ4.5×30) ×6
STEP 1
STEP 1
Mark the wall with template and install the bracket.
Chassis Assy must be installed on a rigid and
even surface.
Caution
Failure to do this may cause damage or personal injury when
3-9/16" (90mm) it falls.
2-3/8" (60mm)
Attach the bracket firmly on the rigid wall with the three screws (φ4.5×30)
2-3/8" (60mm)
・
provided.
In the case of a tile or concrete wall, please use plastic plug anchors with
・
screws provided.
1-9/16" (40mm)
Finished
wall
Junction box
(Actual Placement)
1-9/16"
(40mm)
3-1/8"
2-3/4" 2" (50mm)
(80mm)
(70mm)
1-3/16" (30mm)
2-3/4"
(70mm)
Wall thickness needs
to be 5 to 30mm.
Bracket (Bottom)
Finished Wall
Beam/Stud
Wall
1-9/16" (40mm)
Recommended mounting bracket heights from floor are as follow:
*
- Male/Female: 29-1/2" (750 mm)
- Children: 23-1/2" (598 mm)
- Handicapped: 21-1/2" (547 mm)
w/o Top Cover
Terminal Block
△
<View with cover removed>
Template
5/8 〝 (15mm) Hole Diameter for Electrical Connection
JUNCTION BOX UNDER POSITION
Open space for CLEAN DRY
H:29-7/8"(760mm)
Open space for CLEAN DRY W:12-5/8"(320mm) Min. JUNCTION BOX space in wall
Min JUNCTION BOX space requirement in wall.
TOTO
5-5/16" (135mm) Min. space in wall.
3-9/16" (90mm)
2-3/8" (60mm)
2-3/8" (60mm)
Finished
wall
Junction box
(Actual Placement)
1-9/16"
(40mm)
2" (50mm)
1-3/16" (30mm)
2-3/4" (70mm)
2-3/4" (70mm)
3-1/8" (80mm)
To be continued on the back