Black Max BM803300H Manual Del Operador página 11

 Lift the machine and slide the axle into the wheel mount-
ing hole in the machine base as shown.
 Push the hitch pin into the hole on the end of the axle to
secure the wheel assembly.
NOTE: The hitch pin should be pushed into the axle until
the center of the pin rests on top of the axle.
 Repeat with the second wheel.
INSTALLING THE HANDLE
See Figure 3.
The handle is shipped in the storage position. Before using,
move the handle to the operating position.
 Push and hold the buttons on the frame, then slide the
handle over the lock buttons and remove the handle from
the frame.
CAUTION:
Be careful to avoid pinching your fingers or hands when
installing the handle onto the frame.
 Turn the handle so that the handle is facing away from
the pressure washer. Push and hold the buttons on the
frame as you slide the handle over the lock buttons on
the frame.
INSTALLING THE STORAGE PANEL
See Figure 4.
 Align the holes in the storage panel with the holes in the
handle, as shown.
 Thread the screws into the holes. Tighten securely using
a Phillips screwdriver (not provided).
CONNECTING THE SPRAY WAND TO THE
TRIGGER HANDLE
See Figure 5.
 Place the threaded end of the spray wand in the connec-
tor on the end of the trigger handle.
 Turn the connector as shown until it stops. This secures
the spray wand in place.
CONNECTING THE HIGH PRESSURE HOSE
TO THE TRIGGER HANDLE
See Figure 6.
 Screw the collar on the high pressure hose into the
trigger handle inlet coupler by turning the hose collar
clockwise. Tighten securely.
NOTE: Be careful to avoid cross-threading, which can
cause the trigger handle to leak during use.
 Pull on the hose to be certain it is properly secured.
CONNECTING THE HIGH PRESSURE HOSE
TO THE PUMP
See Figure 7.
 Completely uncoil and straighten the high pressure hose
to prevent kinks.
ASSEMBLY
NOTE: See Using the High Pressure Hose in Operation
for more information about using the high pressure hose.
 Align the collar on the hose to the threaded outlet on the
pump.
 Install the high pressure hose collar onto the threaded
outlet.
 Turn the hose collar clockwise to tighten the hose securely
to the pump.
NOTE: Be careful to avoid cross-threading, which can
cause the hose to leak during use.
 Pull on the hose to be certain it is properly secured.
CONNECTING THE GARDEN HOSE TO THE
PRESSURE WASHER
See Figure 8.
NOTICE:
Always observe all local regulations when connecting
hoses to the water main. Some areas have restrictions
against connecting directly to public drinking water sup-
ply to prevent the feedback of chemicals into the drinking
water supply. Direct connection through a receiver tank
or backflow preventer is usually permitted.
The water supply must come from a water main. NEVER use
hot water or water from pools, lakes, etc. Before connecting
the garden hose to the pressure washer:
 Run water through the hose for 30 seconds to clean any
debris from the hose.
 Inspect the screen in the water intake.
 If the screen is damaged, do not use the machine until
the screen has been replaced.
 If the screen is dirty, clean it before connecting the garden
hose to the machine.
To connect the garden hose to the machine:
 Completely uncoil the garden hose or remove completely
from reel to prevent kinks.
NOTE: There must be a minimum of 10 feet (3 m) of un-
restricted hose between the pressure washer intake and
the hose faucet or shut off valve (such as a "Y" shut off
connector).
 With the hose faucet turned completely off, attach the
end of the garden hose to the water intake. Tighten by
hand.
NOTICE:
Do not run the pressure washer without water supply
connected and turned on, as this may damage the high
pressure seals and decrease pump life. Completely
unwind the hose from its reel or coil and make sure the
hose is not being restricted by tires, rocks, or any other
objects that may lessen or prevent water flow to the
pressure washer.
Page 7 — English