Pre-Operation Inspection - RIDGID HB382 Manual Del Usuario

All benders come with appropriate formers and corner supports for the size range, and are packaged in a
reusable wooden crate. Formers are for pipes to EN10255 and equivalent as listed below:
Former
Nominal Pipe
Size
Catalog No.
Inch
1
37218 / "
4
3
37223 / "
8
37228 1 / "
2
3
37233 / "
4
37238 1"
37243 1 1 / "
4
37248 1 1 / "
2
37253 2"
37258 2 1 / "
2
37263 3"
* Bend radius to centerline of pipe.

Pre-Operation Inspection

WARNING
Before each use, inspect your pipe bender and cor-
rect any problems to reduce the risk of serious inju-
ry from electric shock, crushing injuries and other
causes and prevent machine damage.
1. If an electric bender, make sure the ON/OFF switch
is in the OFF ( ) position and the power cord is
un plugged.
2. Clean any oil, grease or dirt from the pipe bender,
including the handles and controls. This allows bet-
ter inspection of the pipe bender and helps prevent
the pipe bender or control from slipping from your
grip during use.
3. Inspect the bender for:
• Hydraulic leaks. Check the hydraulic fluid level
and adjust as needed (see Maintenance Section).
• Any broken, cracked, bent, missing, misarranged
or binding parts or any other condition that may
prevent the safe and normal operation of the
bender.
• Cracks or breaks in the formers and corner sup-
ports.
Pipe O.D. Wall Thickness
MIN.
Inch mm
Inch mm
0.540 13,5 0.08 2,2
0.675 17,2 0.09 2,3
0.840 21,3 0.10 2,6
1.050 26,9 0.10 2,6
1.315 33,7 0.13 3,2
1.660 42,4 0.13 3,2
1.990 48,3 0.13 3,2
2.375 60,3 0.14 3,6
2.875 76,1 0.14 3,6
3.500 88,9 0.16 4
** See description for more information.
Hydraulic Pipe Bender
Bend Radius*
MAX.
Inch mm
Inch mm
0.16 4 2.36 60
0.16 4 1.77 45
0.16 4 1.97 50
0.16 4 3.15 80
0.20 5 4.33 110
0.20 5 5.31 135
0.20 5 6.10 155
0.22 5,5 8.66 220
0.28 7 12.60 320
0.30 7,6 15.35 390
• Inspect the power cord and plug for damage or
modification, such as cuts or a missing ground
plug.
• Presence and legibility of the warning label. See
Figure 4A and 4B.
If any issues are found during the inspection of the
bender, do not use until those issues have been cor-
rected.
Manual
Figure 4A – Warning Label (Manual)
Weight
Pipe**
Type/Standard
lbs kg
2.2 1 EN10255, ASTM A53
1.8 0,8 EN10255, ASTM A53
2.4 1,1 EN10255, ASTM A53
4.0 1,8 EN10255, ASTM A53
4.0 1,8 EN10255, ASTM A53
4.6 2,1 EN10255, ASTM A53
9.5 4,3 EN10255, ASTM A53
14.4 6,5 EN10255, ASTM A53
38.5 17,5 EN10255, ASTM A53
59.9 27,2 EN10255, ASTM A53
7