golmar GB2 Guía Rápida página 4

NEXA MODULAR GB2 VIDEO DOOR ENTRY SYSTEM KIT - VILLAS
SAFETY PRECAUTIONS
- Always disconnect the power supply before making modifications to the device.
- The installation and handling of these devices must be carried out by
40 cm away from any other wiring
- The wiring must run at least
- In the power supply unit:
Do not overtighten the screws on the connection block.
w
Install the power supply in a dry and protected place free
w
Avoid locations that are humid, dusty or near heat sources.
w
Do not block ventilation holes of the equipments so that air can circulate freely.
w
To avoid damage, the power supply has to be
w
To prevent electric shock, do not remove the cover or handle the wiring connected to the
w
terminals.
( ) CHARACTERISTICS
*
- Video door entry system with simplified installation (non-polarised 2 wire bus).
- Up to 4 access panels (DP-GB2 distributor required for more than one access panel) per installation. A
- Up to 2 apartments (N5110 Vesta2 1-apartment kit and N5220 Vesta2 2-apartment kit) per installation.
- Maximum 23 Vesta2 monitors per installation.
- Maximum 16 Vesta2 monitors in one apartment.
- Maximum 4 Vesta2 monitors in parallel (without distributors) per installation.
- Call confirmation tone.
- Visual indications on the door panel for people with impaired hearing (indicating call process,
communication, door open and channel busy).
- Audible indications on the door panel for people with impaired vision (indicating call
you can speak now, resident unavailable
busy, try later).
SYSTEM OPERATION
- To make a call, the visitor must press the button of the apartment; an audible sound indicates that
the call is being made and LED will turn on. If vocal synthesis is
will indicate a call is being made. At this moment the apartment's monitor(s) receives the call
During the call the visitor can correct his call by pressing a push button corresponding to a
different apartment, in which case the original call is cancelled.
- In systems with several access doors, the other door panel(s) will be automatically disconnected.
If another visitor tries to call, a telephone tones will be heard to indicate that the system is busy
will illuminate If vocal synthesis is activated, the message "System is busy, try later"
and LED .
will be indicated on the door panel.
- The call lasts for 40 seconds. The image appears on the monitor (with code 0 "apartment 1" or
monitor 16 if the call is in "apartment 2") when receiving the call without the visitor knowing.
If the call is not answered within 40 seconds, LED
- To establish communication, press button
LED will turn on. If the vocal synthesis is
heard confirming the communication is activated.
- Communication will last for one and a half minutes or until button
communication has finished, LEDs and
synthesis is activated, a "Communication is finished" message will indicate that the call is over.
- To open the door, press button during the call or communication processes: one press will
activate the lock release for five seconds and LED
synthesis is activated, a "Door is open" message will be indicated on the door panel.
- For a description of the functioning and setup of the monitor, see the monitor's user manual.
( ) For more information, see the "TKIT632 VESTA2 User Manual (code 5012
*
https://doc.golmar.es/search/manual/50122084
authorised personnel
.
without risk of drip or water projections
firmly fixed.
is in progress,
, door is open, c ommunication is finished and
, a "Call is in progress"
activated
will turn off and the channel will be freed.
on any monitor in the apartment. Door panel
the message "you can speak now" will be
activated
is pressed again When
will turn off and the channel will be freed If vocal
will also turn on for five seconds If vocal
A 2084 )".
2
NEXA MODULAR GB2 VIDEO DOOR ENTRY SYSTEM KIT - VILLAS
DOOR PANEL INSTALLATION
( )
*
Positioning the embedding box:
.
Make a hole in the wall to position the top of the door panel at a height of 1.65m.
.
Hole dimensions NCEV-90CS embedding box, 99(W) x 13 ,5(H) x
( )
Description of the door panel LED lights (for low light conditions).
*
( )
Description of the visual indications on the door panel.
*
( ) Description of the vocal synthesis (audible indications on the door panel).
*
( ) Selecting the vocal synthesis language and adjusting the vocal synthesis volume.
*
( )
Configuring the contact type for Relay 1 and Relay 2 (lock release).
*
Adjusting the door panel communication volume.
system is
If after starting the system the door panel audio volume seems inadequate, follow these steps:
- Call an apartment.
-The call is received in the apartment. Establish communication by pressing the push
button on the monitor.
- Next, press the push button used to call the apartment for 3 seconds until a number of
.
confirmation tones are heard and the door panel communication LED starts to blink.
- Each press on the same call button will increase the door panel volume and LED blink speed.
.
There are 5 volume settings and the blink speed of LED
blink - low to high volume. After reaching "setting 5", that is, maximum blink speed and volume,
the next setting is "setting 1", that is, minimum blink speed and volume (carousel mode).
-
To save the volume setting keep the push button used to call the apartment pressed until a
confirmation tones are heard and the door panel communication LED turns off.
LOCK RELEASE INSTALLATION
( )
*
.
Lock release installation instructions:
.
If the lock release is to be fitted to a metal door, use a Ø3.5mm drill bit and
thread the hole made. For wooden doors, use a Ø3mm drill bit.
.
IMPORTANT: The lock release must be Golmar 12V AC or DC.
AC lock release (TF-104 power supply required), fit the varistor supplied with
the kit directly to the lock release terminals to ensure the device functions
correctly.
( ) For more information, see the "TKIT632 VESTA2 User Manual (code 5012
*
https://doc.golmar.es/search/manual/50122084
1850
1650
1450
: 2
will increase for each. Slow to fast
A
3
56,5 (D) mm.
3.5 x 25
DIN-7972
( ) With the
*
M 4 x 8
DIN-963
2084 )".