Operating Your Thermostat - Cadet SBFT2 Instrucciones De Instalación

INSTALLATION INSTRUCTIONS (continued)
Part 2 - Wiring Instructions (continued)
RIGHT
Wiring
Compart-
ment
GROUND
SCREW
A.
Cut closed end splice
from baseboard lead wires.
Strip 1/2" of insulation from
these two cut wires.
Part 3 - Completion of Installation
STEP 1
Be sure the panel of the
baseboard does not interfere with
the mounting of the thermostat
plate. Move panel if needed.
(Using a rubber-coated tool,
or hammer handle; carefully
pry upwards.) See page 1 for
complete instructions.

Operating Your Thermostat

This thermostat will load its default settings after power is established for the first time.
Refer to the General Programming Operation Guide included for complete programming and operating instructions of
your SBFT2 thermostat.
The heater and thermostat must be properly installed before they are used.
For more effective and safer operation and to prolong the life of
the heater, read the Owner's Guide and follow the maintenance
instructions. Failure to properly maintain the heater will void any
warranty and may cause the heater to function improperly. War-
ranties are non transferable and apply to original consumer only.
Warranty terms are set out below.
LIMITED ONE-YEAR WARRANTY: Cadet will repair or replace
any Smart-Base (SBFT2) thermostat found to be defective within
one year after the date of purchase.
These warranties do not apply:
1. Damage occurs to the product through improper installation or
incorrect supply voltage;
2. Damage occurs to the product through improper maintenance,
misuse, abuse, accident, or alteration;
3. The product is serviced by anyone other than Cadet;
4. If the date of manufacture of the product cannot be deter-
mined;
5. If the product is damaged during shipping through no fault of
Cadet.
6. CADET'S WARRANTY IS LIMITED TO REPAIR OR RE-
PLACEMENT AS SET OUT HEREIN. CADET SHALL NOT BE
LIABLE FOR DAMAGES SUCH AS PROPERTY DAMAGE OR
FOR CONSEQUENTIAL DAMAGES AND/OR INCIDENTAL EX-
PENSES RESULTING FROM BREACH OF THESE WRITTEN
WARRANTIES OR ANY EXPRESS OR IMPLIED WARRANTY.
Page 3
J5L2
Terminal
B.
Join the wire from the
baseboard element (bottom)
with the wire from thermostat
terminal J5L2 with a wire
connector.
STEP 2
Carefully push wiring back into the wiring compartment.
Keep all wires away from the Smart-Base circuit board.
These wires may interfere with the clock and thermostat's
performance. Hook upper edge of thermostat under lip of case.
Lower the bottom edge of thermostat to wiring compartment
surface and secure with mounting screw.
Be sure all four wire connectors are tight and secure.
C.
Join the wire behind deflector
(top) with the wire from thermostat
terminal J1T1 with a wire
connector.
Warranty
7. IN THE EVENT CADET ELECTS TO REPLACE ANY PART
OF YOUR CADET PRODUCT, THE REPLACEMENT PARTS
ARE SUBJECT TO THE SAME WARRANTIES AS THE PROD-
UCT. THE INSTALLATION OF REPLACEMENT PARTS DOES
NOT MODIFY OR EXTEND THE UNDERLYING WARRANTIES.
REPLACEMENT OR REPAIR OF ANY CADET PRODUCT OR
PART DOES NOT CREATE ANY NEW WARRANTIES.
8. These warranties give you specific legal rights, and you may
also have other rights which vary from state to state. Cadet nei-
ther assumes, nor authorizes anyone to assume for it, any other
obligation or liability in connection with its products other than as
set out herein.
If you believe your Cadet product is defective, please contact
Cadet Manufacturing Co. at 360-693-2505, during the warranty
period, for instructions on how to have the repair or replacement
processed. Warranty claims made after the warranty period has
expired will be denied. Products returned without authorization
will be refused.
Parts and Service
Visit cadetheat.com/parts-service for information on where to
obtain parts and service.
Reduce-Reuse-Recycle
This product is made primarily of recyclable materials.
You can reduce your carbon footprint by recycling this
product at the end of its useful life. Contact your local
recycling support center for further recycling instruc-
tions.
J1T1
Terminal
D.
Connect each of the
remaining two power supply
leads to each lead from the
thermostat rocker switch with a
wire connector.
Proceed to Part 3.
STEP 3
At this point, the baseboard should be securely
mounted, and the SBFT2 thermostat wired and
secured to the baseboard junction box. The
other junction box should have the baseboard
end plate/cover secured in place.
Verify that the thermostat rocker switch is in the
"O" (OFF) position before reestablishing the
electrical power at the panel for power flow to
the baseboard heater.
©2015 Cadet Printed in USA Rev 02/15 #720004