Hyundai T-Connector Instrucciones De Instalación

Installation Instructions
Directives de Montage
Instrucciones de Instalación
T-Connector
Connecteur en T
Conector en T
Hyundai Sonata
WARNING
ALWAYS read and follow all warnings and
instructions included with purchase before
beginning installation. Keep for future reference.
DO NOT exceed lower of towing manufacturing
rating (including in your vehicle owner's manual)
or specific amperage ratings stated on product.
ALWAYS read, understand and follow all
warnings and instructions printed on tow
vehicle's battery.
ALWAYS wear safety glasses and use all safety
precautions during installation.
118762-037 Rev. A
ENGLISH
TOOLS REQUIRED:
Trim Panel Remover, 10mm Socket & Ratchet
or 10mm Wrench, Drill (3/32" Drill Bit), 1/4"
socket, Wire Crimpers, Wire Cutters, Philips Head
Screwdriver, Test-probe
1. Open trunk. Temporarily remove the rear threshold
plate. Partially remove the felt trunk liner behind the
A b
taillights.
2. On the driver and passenger sides of the vehicle,
locate the vehicle's taillight wiring harness. The
taillight wiring harness will have a connection point,
on both sides, matching the ends of the T-One
Connector. Separate this connector, being careful
not to break the locking tabs. All connector surfaces
should be clean and free of dirt.
3. On the driver's side, insert the T-One
end, with the yellow wire, between the vehicle
wiring connectors and lock into place. Be careful
not to damage the locking tabs and be sure that
connectors are fully inserted with locking tabs in
place.
4. Route the T-One Connector end with green wire to
®
the passenger 's side behind the panels and along
the threshold. Plug the T-Connector end with the
green wire in-between the mating plugs on the
Passenger's side taillight socket and vehicle wiring
harness.
A
58/10/2017
B
5. Locate a suitable grounding point near the
connector. Clean dirt and rustproofing from the
area. Drill a 3/32" hole and secure the white wire
using the eyelet and screw provided.
CAUTION
Verify what is behind any surface prior to drilling to
avoid damage to the vehicle and/or personal injury.
Do not drill into any exposed surfaces.
6. Locate the battery inside the vehicle's trunk.
From inside the vehicle, connect the black 12 ga.
wire and the black wire from the T-One
black box with the supplied yellow butt connector.
7. Disconnect the vehicle's Negative (-) battery cable.
®
If not removed, remove the fuse from the yellow
fuse holder (provided). After cutting the fuse holder
wire, attach the ring terminal and secure to the
C
vehicle's Positive (+) battery cable. Connect the
® Connector
other end of the fuse holder to the black 12 ga.
wire, using the yellow butt connector (provided).
E F
WARNING
Read and follow all warnings and cautions printed
on the tow vehicle's battery.
8. Reconnect the vehicle's Negative (-) battery cable
and install the 15 amp fuse into the fuse holder
from step 7.
WARNING
All connections must be complete for the T-One
Connector to function properly. Test and verify
installation with a test light or trailer once installed.
For initial test, reset vehicle electrical system by
temporarily removing the key from the ignition.
D
E
C F
9. Locate a flat surface in an out of the way place and
10. Secure the remainder of the T-One
11. Replace carpet, and any other clips or panels that
D
Connector
®
®
mount the T-One Connector's black box-module,
®
to prevent damage or rattling.
harness with the cable ties provided, to prevent
damage or rattling and being careful to avoid any
areas that would pinch, cut or melt the wire.
were removed during installation being careful not
to cut or pinch the wires.
NOTE
Store 4-Flat in trunk area when not in use.
WARNING
Overloading circuits can cause fires. DO NOT
exceed stated product ratings. Read vehicle's
owner's manual & instruction sheet for additional
information.
® T-Connector