Final Assembly - Arke Civik Instrucciones Para El Ensamblaje

B11, B12, B83 and B02 (fi g. 1).
29. Find the handrail piece marked with letter "M" (A06) and the one with letter "R" (A04) which will be used for the
railing of the landing (E03) (fi g. 11).
30. Start to model the handrail pieces (A06) marked with "M", in order to give it the handrial staircase's shape most
alike (fi g. 1).
31. Beginning from the baluster (C03) on the landing (E03), start to fi x the handrail (A06),that you have already
slightly bent in the previous operation. Use the parts B16 together with the screw driver and the item B84.
32. Connect all other handrail pieces (A06), by screwing, glueing and shaping them. Use the parts B33 and the
glue (X01).
33. When you reach the fi rst baluster (C03) at the bottom of the stair, cut the excess piece of the handrail with a
hacksaw.
34. Complete the handrail (A06) by assembling the part A07. Use the parts B16 and the glue (X01) (fi g. 1).
35. Fit all remaining railing balusters into the treads (L02), tighten the part B02 and fi x to the handrail (A06), paying
attention to the vertical position(for the stairs with a diameter larger than 140cm(4' 7 1/8"), we suggest that you
fi rst assemble the shorter balusters) (fi g. 12).
36. Check again the regular shape of the handrail (A06) and, if necessary, correct it with a rubber hammer.
37. Complete the railing assembly by fi tting the parts B82 into the lower part of the balusters (C03) (fi g. 1).
Assembly of the Balustrade
38. Screw the baluster (C04) into the part G01 that sticks out from the landing (E03) (fi g. 10).
39. Assemble the parts F01 into the holes of the landing (E03), using the parts B07, B06, B23 (fi g. 1).
40. Position the shorter balusters (C03) and tighten the part B02 (fi g. 1)
41. Fix the part A05 into the baluster (C04), by using the part B02 (fi g. 1).
42. Fix the handrail (A04) marked with the letter "R", using the parts B16 (fi g. 1).
43. In case there were walls around the stair and depending on their position, it could be necessary to set one or
two more balusters (C03) (fi g. 12).
44. In that case it is necessary to consider either the distance between all other balusters, or otherwise the
distance from the wall. For the fi xing it is suggested to drill the landing (E03) with drill bit Ø9 and to use the
fi xing parts F01, B02, B07, B06, B23. Whereas for the fi xing into the fl oor it is suggested to drill with drill bit Ø
12 and to use the parts F01, B02, B87 (fi g. 13).

Final Assembly

45. In order to tighten the staircase at the intermediate points, you must fi x into the wall the parts F09 and connect
them to the balusters (C03) by using the part F08. Drill the wall with a drill bit 8 and use the parts B85, B86,
B11, B12 (fi g. 14).
46. Stick the panels (H06) to the treads (L02) using the part B96 (fi g. 1).
47. Stick the panels (H03, H04), to the landing (E03) using the part B96 (fi g. 1).
We would be grateful, if you could send us any possible suggestion by visiting our Internet Site:
www.arke.ws
7 - ck