Dry Ironing; Steam Ironing - Shark GI490 N Manual Del Propietário

INSTRUCCIONES DE USO
9. Cuando la plancha esté vacía, gire el
regulador de vapor a la posición "0".
10. Coloque la plancha en posición
vertical sobre su talón y espere a que
se enfríe antes de guardarla.
Fig. 8
ALMACENAJE
1. Siempre gire el regulador de vapor a la
posición "0" después de vaciar el agua
de la plancha.
2. Deje que la plancha se enfríe.
3. Siempre guarde la plancha en posición
vertical para proteger la base de la
plancha.
4. Limpie el exterior de la plancha
ocasionalmente con un paño húmedo
y séquela frotándola.
5. Si usa un rociador de almidón para
planchar, frote la base de la plancha
ocasionalmente con una tela suave
húmeda para evitar la acumulación
del almidón.
6. Si la plancha no se hubiese usado
por varias semanas, sosténgala
horizontalmente y deje que despida
vapor por 2 minutos antes de
planchar
NOTA:
La función antigoteo reduce el
goteo de agua y las manchas, pero no
lo hará si no se presiona el botón para
chorros súbitos de vapor con frecuencia,
o si la temperatura de la plancha está
demasiado baja. La cantidad del goteo
de agua irá disminuyendo después
utilizar la plancha para vaporizar dos
o tres tanques completos de agua.
19
OPERATING INSTRUCTIONS
IMPORTANT: This
appliance is for
HOUSEHOLD USE ONLY and may be
plugged into any 120V AC polarized
electrical outlet. Do not use any other
type of outlet.
FABRIC & TEMPERATURE
INDICATORS
Press on the Electronic Temperature
Control to select the desired fabric
setting. The red lights at the left of the
LED Display Panel will light up.
At the same time, the temperature
indicator lights on the right side of the
LED Display Panel will start to flash.
They will stop flashing when the iron
reaches the selected temperature.

DRY IRONING

For dry ironing, turn the variable steam
control dial all the way to the right to "0".
This will cut off the steam flow if water is
in the water tank. All marked fabric
settings on the LED Display Panel can
be used for dry ironing.
1. Plug the cord into a polarized, 120V
AC electrical outlet. The power "ON"
light will come on, indicating that the
iron is receiving power.
2. Press on the electronic temperature
control button to select the desired
fabric/temperature setting. Turn the
variable steam control dial to "0".
(See "Ironing Guide" for a guide to
temperature selection.)
3. Place iron on its heel (on a stable,
protected surface) while iron is
warming to desired temperature.

STEAM IRONING

WARNING!
Before filling the iron
with water, be sure the iron is not
plugged into the electrical outlet.
The iron may be filled with water
while it is hot.
CAUTION!
TO PREVENT THE RISK
OF BURNS, use caution when filling
iron with water. Burns can occur
from touching hot metal parts, hot
water, or steam.
NOTE: Because of the soleplate design,
ordinary tap water may be used with this
iron. However, in very hard water areas,
we recommend using distilled or
demineralized water.
WARNING
: Never fill the iron
with fabric conditioner, starches
or any other liquid, as these will
damage the steam mechanism.
Do not use contaminated water.
1. Open the water filling inlet cover.
Holding the iron at a slight angle,
pour water slowly into the water
filling inlet (see figure 1). Fill tank to
desired level or to the "MAX" water
level marking using the water filling
flask (when the iron is upright, the
see-through water tank allows you to
gauge the amount of water). DO
NOT overfill the tank. When finished
filling the iron with water, close the
water inlet cover before continuing.
Fig. 1
CAUTION!
DO NOT aim iron at
face, towards yourself, or anyone
else while using or adjusting
steam. Burns or serious injury
may occur.
2. Plug the cord into a polarized, 120V
AC electrical outlet.
3. Press on the electronic temperature
control button to select the desired
fabric and temperature setting. Turn
the variable steam control dial to
the desired steam setting (see
"Ironing Guide" for a guide to
temperature selection).
4