Clatronic KM 2894 Profi Cook Instrucciones De Servicio/Garantía página 80

❲ ✁ ✂ ✄ ✂ ✄ ✁ ☎ ✆ ✝ ✞ ✁ ✟ ✝ ✠ ✁ ✡ ☛ ☞ ☎ ✂ ✌ ✍ ☎ ✝ ✟ ✎ ✡ ✆ ☎ ✠ ✏ ✎ ☞ ✟ ✑ ✡ ✒
⑧ ✉ ✓ ✔ ✕ ✖ ✗ ✘ ✕ ✙ ✚ ✛ ✜ ✈ ✢ ✣ ✕ ✉ ✘ ✚ ✤ ✥ ✦ ✛ ✜ ✣ ✕ ✦ ✓ ✜ ✧ ✔ ✦ ✢ ② ★
⑧ ✥ ✛ ✜ ✔ ✉ ✓ ✔ ✕ ✖ ❜ ✕ ✙ ✩ ✦ ✛ ✓ ✛ ✕ ✦ ✪ ✜ ✙ ✙ ❜ ✛ ✥ ✜ ✔ ✔ ✛ ✦ ★
⑧ ✥ ✛ ✜ ✔ ✉ ✓ ✔ ✕ ✖ ✗ ✘ ✕ ✙ ❜ ✫ ✘ ✚ ✔ ✣ ✕ ✉ ✘ ✚ ✤ ✛ ✳ ✘ ✳ ✙ ✕ ✦ ✩ ✕ ✕ ✗ ✫ ✛ ✧ ② ✳
: Do not operate the device for more than 50 seconds at maximum
❈ ✬ ✭ ✮ ✯ ✰ ✱
level when working heavy dough!
6. After kneading/stirring turn the switch (2) back to position „0" as soon as a
small amount or ball of dough has formed. Then remove the mains plug.
7. Turn the lid to the left and remove it from the processor bowl.
8. The processor bowl can now be removed. The fi nished dough can be re-
leased from the sides and with a spatula (29) and taken out of the bowl.
9. Clean the used parts as described in „Cleaning".
: The chopper is very sharp!
❲ ✬ ❆ ✱ ✯ ✱ ✿
Take the chopping knife (17) and remove it carefully from the protective cover
(18).
1. The safety cover (5) must be mounted on the drive shaft for the mixing drive
(3).
2. Mount the processor bowl as described.
3. Attach the chopping knife directly over the drive shaft (8).
4. Now fi ll in your ingredients. Please note the markings on the processor bowl
and do not fi ll it above them.
5. Place the lid in position on the processor bowl. Turn it to the right until it is
heard to lock in place.
6. Close the fi ller shaft (11) with the stopper (12).
7. Switch on the appliance and set a speed between 1 and 6 with switch (2). You
will achieve better results if you use the pulse mode (see the section „Mixing
Operation").
8. After chopping, turn the switch (2) back to „0" and pull out the plug.
9. Turn the lid to the left and remove it from the processor bowl.
10. The processor bowl can now be removed. The contents can now be taken out
of the bowl .
11. Clean the used parts as described in „Cleaning".
1. The safety cover (5) must be mounted on the drive shaft for the mixing drive
(3).
2. Mount the processor bowl as described.
3. Push the locating pin (21) over the drive shaft (8).
4. Insert the grater (23) or a rasp (24, 25) into the recess of the attachment
holder (22). Press the grater or rasp fi rmly until it is heard to lock into place.
❇ ❊ ❊ ❊ ❊ ❋ ❍ ❇ ❋ ■ ❏ ❑ ▲ ▼ ◆ ❖ € ◗ ❘ ❙ ❚ ◗ ◗ ❯ ❱ ▼
✲ ✴ ✵ ✶ ✶ ✷ ✸ ✹ ✺ ✷ ✻ ✴ ✻ ✴ ✼ ✽ ✴ ✵ ✶ ✶ ✼ ✾
❉ ✑ ✡ ❀ ✝ ❁ ✎ ❂ ✁ ✡ ☛ ☞ ❁ ✏
✲ ❃ ✻ ✻ ✷ ✸ ✹ ❄ ✸ ❅ ✹ ✾ ❄ ✻ ✷ ✸ ✹
!
❑ ❳ ❊ ❍ ▲ ❊ ❑ ❍ ❍ ◆ ❨ ❩ ❱ ❬ ❭ ❩ ❬ ❇ ◆ ❪ ❫ €
●
79