Publicidad
Idiomas disponibles
Idiomas disponibles
General safety
WARNING! Read all safety warnings and
all instructions. Failure to follow these
may result in serious (eye) injury.
Save all warnings and instructions for future reference.
•
Never make warning labels on the measuring tool
unrecognisable.
•
The measuring tool is delivered with a warning label
in German language (marked with the position F in
the representation of the measuring tool on the
graphic page). Before putting into operation for the
first time, attach the supplied sticker in your national
language over the German text on the warning label.
Do not remove or damage the warning label on the tool.
•
Do not direct the laser beam at persons or
animals and do not stare into the laser
beam yourself (not even from a distance).
This measuring tool produces laser class 2
laser radiation according to EN 60825-1. This
can lead to other persons being unintentionally blinded.
•
Do not place the tool in a position that may cause
anyone to look into the laser beam intentionally or
unintentionally.
•
Do not use the laser viewing glasses as safety
goggles. The laser viewing glasses are used for
improved visualisation of the laser beam, but they do not
protect against laser radiation.
•
Do not use the laser viewing glasses as sun glasses
or in traffic. The laser viewing glasses do not afford
complete UV protection and reduce colour perception.
•
Do not use any magnifying optical tools (such as
magnifying glasses, telescopes, or binoculars) to
view the laser beam
•
Have the measuring tool repaired only through
qualified specialists using original spare parts. This
ensures that the safety of the measuring tool is
maintained.
•
Do not allow children to use the laser measuring tool
without supervision. They could unintentionally blind
other persons.
•
Do not operate the tool in the presence of flammable
liquids, gases or dust.
•
Do not use the tool for any purpose other than those
mentioned in this instruction manual.
•
Only use the original accessories which are intended
for this tool.
•
Always switch off the tool when not in use.
Technical specifications
Model
Type number
Laser type
Laser class
Batteries (included)
Operating temperature [°C]
Storage temperature
Weight
Accuracy
0502
F 012 050 2..
[nm]
635
2
3 x AG13 button cell battery
-10°C to 40
[°C]
-20ºC to 60
kg
0,05
deviation of +/- 10 mm at 5
metres distance
Tool elements
A
On/off switch
B
Bubble level for horizontal lines
C
Bubble level for vertical lines
D
Laser light opening
E
Battery compartment cover
F
Warning label
G
Suction accessory
H
Clamp accessory
J
Pin accessory
K
Magnet accessory
L
Screw accessory
M
Pivot accessory
N
Belt clip accessory
* Not all of the accessories illustrated or described are
included as standard delivery.
Introduction
This tool is intended for aligning objects and/or marking
desired cutting lines by means of a straight laser line
projection; with the accessories supplied the tool can be
used on a variety of surfaces
Starting operation
ON/OFF
Before first use, remove protective insert as illustrated
(figure 2).
Switch on/off the tool by pushing switch A.
Do not look into the laser beam.
Do not point the laser beam at persons or animals.
Always switch off the tool after use.
Assembly
CHANGING BATTERIES (figure 3).
Ensure that the tool is switched off.
Remove cover E.
Insert 3 x AG13 button cell battery (pay attention to correct
polarisation).
Mount cover E.
Always remove the batteries from the tool, if the tool is not
used for a long period.
Always replace the complete set of batteries.
Operating the tool
When projecting a horizontal line, ensure that the bubble in
level B is centered (figure 4).
When projecting a vertical line, ensure that the bubble in
level C is centered (figure 4).
Make measurements using the projected line as reference
When projecting a laser line at a longer distance, you may
increase its visibility by placing an object at the end of the
desired distance (figure 5).
SUCTION ACCESSORY G (figure 6).
For projecting lines on smooth surfaces.
Slide tool on accessory G.
Place accessory G onto surface.
Level the tool (ensure that the bubble in the relevant level is
centered).
11
GB
Publicidad
