Product Description; Technical Specifications; Battery Replacement - Roger Technology SYNUS/2 Manual De Instrucciones

1

Product description

SYNUS/2 radio remote controls remotely activate motorized doors and gates.
SYNUS/2 radio remote controls are compatible with all H93/RX22A/I, R93/
RX12A/I, R93/RX12A/U Series FIXED CODE receivers, can be configured to
work in Rolling Code mode and can be used with Roger H93/RX2RC/I, R93/
RX2RC/U Series receivers.
The Rolling Code mode uses the RTHSE (Roger Technology High Security)
standard which allows a high level of security to be achieved.
2

Technical specifications

NUMBER OF KEYS
TRANSMISSION LED COLOUR
BIT NUMBER OF THE IDENTIFICATION
CODE
NUMBER OF CODE COMBINATIONS
NUMBER OF BITS TRANSMITTED
TRANSMISSION FREQUENCY AND
MODULATION
MAXIMUM REACH (in unobstructed
environment)
BATTERY AND AVERAGE CONSUMPTION
OPERATING TEMPERATURE
FIXED CLONABLE CODE TYPES
DIMENSIONS (mm)
3
Operating mode selection
The SYNUS/2 radio remote control is configured in the factory to operate in
Fixed Code mode.
To select the "Rolling Code" mode:
1. Press and hold both keys A and B simultaneously.
2. After a few flashes, the LED lights up with a steady RED light.
3. Press and hold both keys A and B.
4. After 5 seconds the LED changes to GREEN: the "Rolling code" operating
mode is active.
To return to the "Fixed code" operating mode, repeat the aforementioned
procedure. The LED should change from GREEN to RED.
In the case of transmission of a (fixed) CLONED code, the flashing alternates
RED ... GREEN ... RED ... GREEN LED, is preceded by:
- fast flash RED LED (if fixed code mode is enabled).
- fast flashing GREEN LED (if rolling code mode is enabled).
4
Storing a remote control key in the receiver
(Fig.2)
1. Check the type of radio receiver installed. If the receiver is the Rolling
Code type, select the SYNUS/2 operating mode as per paragraph 3.
2. Switch the controller unit on.
3. Press P1 or P2 once (depending on the function to be enabled) on the
receiver.
4. When LED L1 or LED L2 on the receiver flashes slowly, press the key on
the transmitter where the function is to be stored.
5. When LED L1 or L2 remains on for 1 second, the transmitter has been stored.
6. LED L1 or L2 flashes slowly again and other transmitters can be stored
during this time.
7. The procedure is automatically exited when no more transmitters are stored.
9
Indicators
Fixed code Transmission
ROGER Code Rolling code transmission
Cloned fixed code transmission (when fixed code mode is enabled)
Cloned fixed code transmission (when Rolling code mode is enabled)
Failure when copying the code. Code not recognized
Battery almost depleted
Battery depleted
4
SYNUS/2
Fixed code Rolling Code
2 2
RED GREEN
16 32
65.536 4.294.967.296
28 144
433,92 MHz
AM/ASK
150 m
1xCR2032 3V 8mA
-10°C +55°C
MANCHESTER, PCM Max. 64 bit
66x34x10,4
(Fig.1)
ACTION
5
Radio remote control copy
1. Press the two keys (A and B) of a NEW radio remote control simultaneously.
2. The LED (RED if Fixed Code mode is enabled - GREEN if Rolling Code mode
is enabled) on the radio remote control flashes slowly until it lights up in
steady light.
3. On the NEW radio remote control, release a key and hold down the key
on which you wish to store the code. The LED flashes briefly for up to 20 s.
4. Zoom in on the NEW radio remote control, the OLD one (the one you want
to copy), as close as possible, and press the key to copy on the OLD radio
remote control.
5. When the LED on the NEW radio remote control is lit for 1 second (RED if
Fixed Code mode is enabled - GREEN if Rolling Code mode is enabled), it
indicates that the copy has been completed successfully.
Warning!
The Synus radio remote control in Rolling Code mode cannot copy the Roger
E80/TX2R/RC or E80/TX4R/RC radio remote controls, or SYNUS/2 configured in
Rolling Code mode. Instead, you can copy the Fixed Code radio remote controls.
Codes copied with radio remote controls in "Fixed Code" mode remain in
memory even when the radio remote control is set to "Rolling Code" mode
and vice versa. Mode shifting does not delete the codes.
6

Battery replacement

1. Using a screwdriver, unscrew the side screw of the radio remote control.
2. Gently rotate one of the two parts.
3. Remove it gently.
4. Remove the battery from its housing.
5. Replace the battery paying attention to the polarity.
6. Close both parts again and tighten the side screw without over-
tightening it.
7
Disposal
This product may only be uninstalled by qualified technical
personnel, following suitable procedures for removing the
product correctly and safely.
This product consists of numerous different materials.
Some of these materials may be recycled, while others must
be disposed of correctly at the specific recycling or waste
management facilities indicated by local legislation applicable
for this category of product.
Do not dispose of this product as domestic refuse.
Observe local legislation for differentiated refuse collection, or hand the
product over to the vendor when purchasing an equivalent new product.
Local legislation may envisage severe fines for the incorrect disposal of this
product. Warning! some parts of this product may contain substances that
are harmful to the environment or dangerous and which may cause damage
to the environment or health risks if disposed of incorrectly.
8
Declaration of Conformity
The undersigned, representing the following manufacturer
Roger Technology - Via Botticelli 8, 31021 Mogliano V.to (TV)
hereby DECLARE that the appliance described hereafter:
Description: Remote control
Model: SYNUS/2
Is in conformity with the legislative provisions that transpose the following di-
rectives:
– 2014/53/EU RED Directive and subsequent changes;
– 2011/65/EU RoHS Directive
and that all the standards and/or technical requirements indicated as follows
have been applied:
EN 300 220-1 V2.4.1:2012-05; EN 300 220-2 V2.4.1:2012-05
EN 301 489-1 V2.1.1, EN 301 489-3 V1.6.1
EN 62479
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+AC:2011
Last two figures of year in which marking was applied | 18.
Place: Mogliano V.to
Date: 18/06/2018
RED LED fast flashing
GREEN LED fast flashing
Fast flash RED LED, follow by RED...GREEN...RED...GREEN alternating flashing
Fast flash GREEN LED, follow by RED...GREEN...RED...GREEN alternating flashing
LED steadily on
Normal flashing with long pauses
Brief fast flashing, repeated at long intervals.
(Fig. 3)
(Fig. 4)
Signature
LED STATUS