Publicidad
Idiomas disponibles
Idiomas disponibles
TERMINAL DESCRIPTIONS (See illustrations):
"POS" Terminal - Output terminal connects to the
Positive (+) battery terminal.
"R" Terminal - Relay terminal carries half systems voltage and
may be used for certain types of control relays, charge indicators,
tachometers or similar devices. The current draw should not
exceed four (4) amperes. Notice! Do not install the remote
sense lead to this terminal.
"I" Terminal - Indicator lamp/Ignition terminal carries full system
voltage. Current draw should not exceed one (1) ampere. It is
recommended current is not drawn from this terminal.
Ground Screw – Ground lead ensures alternator is grounded. A
Ground lead is strongly recommended for optimum performance.
"Remote Sense" Terminal - Monitors batteries system voltage at
the batteries or the common distribution point. The sense terminal
on the 33SI, 34SI & 35SI & 36SI is the fourth terminal and is
identified with a "remote sense" label on the back cover plate.
If installing a remote sense alternator in a vehicle that does not
have a sense line, connect a jumper lead, with a 5 ampere fused
link, from the voltage sense terminal to the positive (+) battery
terminal or the common distribution point. See diagram below.
If installing a non-remote sense alternator in a vehicle that has
a remote sense line, disconnect and secure the wire from the
battery. Notice! Be careful not to ground the leads open end and if
it has a fuse it should be deactivated.
Only connect the remote sense line to the remote sense terminal.
The "R" Terminal is Not the Remote Sense Terminal!
NOTE: Output voltage can be lowered, if necessary, on
34SI, 35SI & 36SI alternators by installing a jumper wire between
the remote sense and battery (+) terminals when a remote sense
line is not used. Use an 18 AWG minimum wire size terminated
with ring terminals to fit. Securely crimp and solder the
connections.
ADDING REMOTE SENSE TO A VEHICLE THAT DID NOT COME WITH A REMOTE SENSE WIRE
Technical support: USA 800 372 0222, Mexico 01 800 000 7378, Brazil 0800 703 3526, South America 55 11 3183 0384
or visit delcoremy.com
NOTICE
- Only licensed Delco Remy products and component parts should be used, and the use of other parts or modifications not approved by
BorgWarner will void all applicable warranties. The failure to carefully follow these Instructions, set forth herein, will void all applicable warranties. Delco
Remy is a registered trademark of General Motors Corporation licensed to BorgWarner PDS (Anderson) L.L.C.
© 2017 BorgWarner Inc. All rights reserved
FROM THE FACTORY
REMOTE SENSE™
AND CLOSE TO BATTERY
TERMINAL
NEW WIRE
Under 10 Feet
use 16 Gauge.
Over 10 Feet use
14 Gauge
33SI, 34SI, 35SI, & 36SI HP REMOTE
SENSE
™
GROUND SCREW (-)
[LOCATION WILL VARY]
5.6-6.8 Nm (50-60 lb in)
OUTPUT (+)
6.2-7.9 Nm
(55-70 lb in)
RELAY PIN TERMINAL MATING CONNECTOR - OBTAIN FROM
DELPHI OR OTHER APPROVED SOURCE IF REQUIRED.
ADDING A REMOTE SENSE LINE
Delco Remy strongly recommends taking advantage
of remote sense technology.
Remote Sense technology allows for a more
complete battery charge and can result in extended
battery life.
ITEMS NEEDED
-
5 Amp Inline Fuse (Sealed)
-
16 or 14 Gauge wire (depending on length)
Ring terminals to fit Remote Sense terminal and
-
Battery Positive terminal.
Convoluted tubing anywhere wire passes metal.
-
NOTE: The fuse and convoluted tubing is to protect the
vehicle from the wire rubbing through to ground.
-
INLINE FUSE 5 AMP
MAIN POSITIVE
CABLE TO
STARTER
2
SENSESENSE
INDICATOR/IGNITION
1.7-2.8 Nm (15-25 lb in)
CONNECT TO MAIN
BATTERY TERMINAL
ONLY
REMOTE SENSE
(OPTIONAL)
1.7-2.8 Nm
(15-25 lb in)
RELAY
1.7-2.8 Nm
(15-25 lb in)
+
-
Publicidad
