Publicidad
Idiomas disponibles
Idiomas disponibles
Chamberlain, Sears, LiftMaster, Master Mechanic, DoIt
Determine if your motor unit/receiver system has DIP switches or a smart-learn button.
(Locate the small gray wire antenna. Some models require removing the light lens.)
TYPE
A
GREEN, RED or ORANGE
With this type receiver, the existing remotes do not contain DIP
switches. Proceed to BRAND MODE SETTINGS.
TYPE
B
YELLOW, WHITE or GRAY
1. Gather any existing remotes and open to expose the DIP
switches labeled "+", "0" and "-". The "0" setting cannot be
used with the Clicker remote.
2. Reset switches: 1 to "-" and positions 2 through 9 to a random
setting using "+" and the "-". DO NOT USE THE "0" SETTING,
SET ALL REMOTES TO THE SAME SETTING.
3. The recoded remotes must be programmed to the receiver.
Press and release the smart-learn button. Then press and hold
the existing remote push button for three seconds.
NOTE: Some three button remotes do not have a #1 switch.
Match the 2 through 9 to the receiver, on three button remotes
the large button is now programmed to activate the door.
4. Test all the newly coded existing remote controls to be sure that
they operate the door before proceeding to program the Clicker
with the BRAND MODE SETTING.
TYPE
C
DIP SWITCHES
The Receiver DIP switch has three positions labeled "+", "0"
and "-". The "0" setting cannot be used with the Clicker
remote.
1. Reset switches: 1 to "-" and positions 2 through 9 to a random
setting using "+" and the "-". DO NOT USE THE "O"
SETTING.
2. Gather any existing remotes and open to expose the DIP
switches. Reset the DIP switch to match the newly coded
receiver. NOTE: Some three button remotes do not have a
#1 switch. Match the 2 through 9 to the receiver, on three
button remotes the large button is now programmed to
activate the door.
3. Test all the newly coded
existing remote controls to
be sure that they operate
the door before proceeding
to program the Clicker with the BRAND MODE SETTING.
TECHNICAL SUPPORT: 800-442-1255
(MONDAY-FRIDAY 6AM-7PM CST; SATURDAY 8AM-6PM)
Chamberlain, LiftMaster and Moore-O-Matic are Trademarks of Chamberlain Group. Genie is a
Trademark of Overhead Door Corporation. Linear and Multi-Code are Trademarks of Linear
Corporation. Master Mechanic is a Trademark of TruServ. Sears is a Trademark of Sears & Roebuck.
Stanley is a Trademark of The Stanley Works. DoIt is a trademark of DoIt Best Corporation.
114A2504B
Learn Button
Learn Button
1 2 3 4 5 6 7 8 9
✚
RANDOM 2-9
O
DO NOT USE
–
Remote
push button
1
Use this
button
Or single
function remote
1 2 3 4 5 6 7 8 9
✚
RANDOM 2-9
O
DO NOT USE
–
©2001, Clicker Corporation
Step 1
BRAND MODE SETTINGS
A
TYPE
GREEN
Smart-Learn Button
ON
ON ON OFF
- OR -
ORANGE/RED
Smart-Learn Button
OFF ON ON OFF
OR
TYPE
B
C
and
2
3
DIP
KG
KG
SWITCHES
Step 2
Step 3
Step 4
Step 5
Use this
button
Step 6
All Rights Reserved
➡
1
2
SMART-LEARN
BUTTON
Set brand switches on
Clicker remote to:
➡
Set brand switches on
Clicker remote to:
➡
ON ON OFF OFF
➡
Existing
Remote
➡
Match
existing codes.
Set extra
switches off.
Press and hold both
buttons for 5 seconds or
until LED begins to flash.
When LED flashes, release
both buttons.
While the LED is still flashing, press the
button you wish to operate the opener
(your choice). For type A, continue on to
Step 5. For type B&C, proceed to Step 6.
1
2
3
A. Press and release
Smart- Learn button.
KG
KG
B. Press and hold button
selected in Step 4 for
3 seconds.
Programming is complete, to
test, press the button selected to activate
garage door.
✚
O
–
DIP SWITCHES
3
KG
KG
Code switch
settings are
not used.
Clicker
Remote
Printed in Mexico
Publicidad
