Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Chrysler CAN data interface 2004-up
• Provides accessory power (12-volt 10-amp)
• Retains R.A.P. (retained accessory power)
• Provides NAV outputs (parking brake, reverse,
and speed sense)
• Prewired ASWC-1 harness (ASWC-1 sold separately)
CHRYSLER
DODGE
300
2005-2007
Caliber
2007-2008
Aspen
2007
Charger
2006-2007
PT Cruiser
2006-2010
Dakota
2005-2007
Durango
2004-2007
CHRYSLER
Caliber
2009-2012
200
2011-up
Grand Caravan
300
2008-2010
Challenger
2008-2014
Aspen
2008-2009
Charger
2008-2010
Sebring
2007-2010
Dakota
2008-2011
Town & Country 2008-up
Durango
2008-2013
Journey
2009-2010
DODGE
Magnum
2008-2009
Avenger
2008-2014
®
Axxess Integrate
Installation instructions for part AW-INCH1
AW-INCH1
INTERFACE FEATURES
• Can be used in both amplified and non-
amplified models
• Retains balance and fade (non-amplified
models only)
• Micro "B" USB updatable
APPLICATIONS
Applications below use the LD-BX-CH1 harness:
Magnum
2005-2007
JEEP
Ram 2500/3500
2009
Commander
Ram
2006-2008
Compass
Ram Chassis Cab
Grand Cherokee
2006-2010
APPLICATIONS
Applications below use the LD-BX-CH2 harness:
Nitro
2007-2011
Grand Cherokee
2008-up
Ram
2010-2011
Liberty
Ram 1500
2009
Patriot
Ram Chassis Cab
2011
Wrangler
JEEP
Wrangler Unlimited
Commander
2008-2010
Compass
2009-up
MITSUBISHI
Raider
axxessinterfaces.com
®
Patriot
2007-2008
2006-2007
MITSUBISHI
2007-2008
Raider
2006-2007
2005-2007
RAM
2008-2013
1500/2500/3500
2012
2008-2012
Chassis Cab
2012
2009-up
C/V Tradesman
2007-up
2012-2015
VW
2007-up
Routan
2009-2013
2008-2009
•
metraonline.com
TABLE OF CONTENTS
Connections to be made ................................................... 2
Installing the AW-INCH1 ................................................... 3
Initializing the AW-INCH1 ................................................. 3
INTERFACE COMPONENTS
• AW-INCH1 interface • LD-BX-CH1 harness
• LD-BX-CH2 harness
TOOLS REQUIRED
• Cutting tool • Tape • Crimping tool
• Connectors (example: butt-connectors, bell caps, etc.)
CAUTION!
All accessories, switches, climate controls panels, and
especially air bag indicator lights must be connected before cycling
the ignition. Also, do not remove the factory radio with the key in the
on position, or while the vehicle is running.
© COPYRIGHT 2017 METRA ELECTRONICS CORPORATION
Publicidad
Resumen de contenidos para Axxess AW-INCH1
- Página 1 • Retains balance and fade (non-amplified INTERFACE COMPONENTS • Provides NAV outputs (parking brake, reverse, models only) and speed sense) • AW-INCH1 interface • LD-BX-CH1 harness • Micro “B” USB updatable • LD-BX-CH2 harness • Prewired ASWC-1 harness (ASWC-1 sold separately) APPLICATIONS...
-
Página 2: Connections To Be Made
® AW-INCH1 Connections to be made From the LD-BX-CH1 OR LD-BX-CH2 harness to the aftermarket radio: The following (3) wires are only for multimedia/navigation radios that require these wires. • Connect the Black wire to the ground wire. • Connect the Blue/Pink wire to the VSS/speed sense wire. - Página 3 Note: If using the ASWC-1, connect it after you initialize and test the until the radio comes on. AW-INCH1, with the key in the off position. Note: If the radio does not come on within 60 seconds, turn the key to the off position, disconnect the interface, check all connections, reconnect the interface, and then try again.
-
Página 4: Important
® Installation instructions for part AW-INCH1 IMPORTANT If you are having difficulties with the installation of this product, please call our Tech Support line at 1-800-253-TECH. Before doing so, look over the instructions a second time, and make sure the installation was performed exactly as the instructions are stated. -
Página 5: Interfase De Datos Chrysler Can 2004 Y Mas
® Instrucciones de instalación para la pieza AW-INCH1 AW-INCH1 Indice Interfase de datos Chrysler CAN 2004 y mas Conexiones que se deben hacer ........2 Instalación del AW-INCH1 ..........3 Inicialización del AW-INCH1 ..........3 CARACTERÍSTICAS DE LA INTERFASE • Proporciona corriente de accesorios (12 voltios •... -
Página 6: Conexiones Que Se Deben Hacer
® AW-INCH1 Conexiones que se deben hacer Desde el arnés LD-BX-CH1 o LD-BX-CH2 al radio de mercado secundario: • Conecte el cable púrpura con la salida positiva de la bocina derecha trasera. • Conecte el cable negro al cable de tierra. -
Página 7: Instalación Del Aw-Inch1
Nota: Si va a utilizar el ASWC-1, conéctelo después de inicializar y and y esperar hasta que la radio se enciende. probar el AW-INCH1 con la llave en la posición de apagado. Note: Si la radio no se enciende dentro de 60 segundos, gire la llave a la posición de apagado, desconecte la interfase, compruebe todas las... -
Página 8: Importante
® Instrucciones de instalación para la pieza AW-INCH1 IMPORTANTE Si tiene dificultades con la instalación de este producto, llame a nuestra línea de soporte técnico al 1-800-253-TECH. Antes de hacerlo, revise las instrucciones por segunda vez y asegúrese de que la instalación se haya realizado exactamente...