Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
16 • ENGLISH
blade and blade clamp. Do not stabilize the saw by
gripping the shoe.
f Keep blades sharp. Dull blades may cause the saw
to swerve or stall under pressure.
f When cutting pipe or conduit ensure that they are
free from water, electrical wiring, etc.
f Allow the motor to come to a complete stop
before withdrawing the blade from the kerf (the
slot created by cutting). A moving blade may impact
the workpiece causing a broken blade, workpiece
damage or loss of control and possible personal injury.
f Never hold work in your hand, lap or against parts
of your body when sawing. The saw may slip and
the blade could contact the body causing injury.
f Keep handles dry, clean, free from oil and grease.
This will enable better control of the tool.
f Clean out your tool often, especially after heavy
use. Dust and grit containing metal particles often
accumulate on interior surfaces and could create an
electric shock hazard.
f Do not operate this tool for long periods of time.
Vibration caused by the operating action of this tool
may cause permanent injury to fingers, hands, and
arms. Use gloves to provide extra cushion, take
frequent rest periods, and limit daily time of use.
Warning! Always use safety glasses. Everyday
eyeglasses are not safety glasses. Also use face or dust
mask if drilling operation is dusty. Always wear certified
safety equipment:
f ANSI Z87.1 eye protection (CAN/CPA Z94.3),
f ANSI S12.6 (S3.19) hearing protection,
f NOSH/OSHA respiratory protection.
Warning! Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to the state
of California to cause cancer, birth defects or
other reproductive harm. Some examples of these
chemicals are:
f lead from lead-based paints,
f crystalline silica from bricks and cement and other
masonry products, and
f arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how
often you do this type of work. To reduce your exposure
to these chemicals: work in a well ventilated area, and
work with approved safety equipment, such as those dust
masks that are specially designed to filter out microscopic
particles.
f Avoid prolonged contact with dust from power
sanding, sawing, grinding, drilling, and other
construction activities. Wear protective clothing
and wash exposed areas with soap and water.
Allowing dust to get into your mouth, eyes, or lay
on the skin may promote absorption of harmful
chemicals.
Warning! Use of this tool can generate and/
or disperse dust, which may cause serious and
permanent respiratory or other injury. Always use
NOSH/OSHA approved respiratory protection appropriate
for the dust exposure. Direct particles away from face and
body
Warning! Wear appropriate hearing protection
during use. Under some conditions and duration of use,
noise from this product may contribute to hearing loss.
When using an extension cord, be sure to use one heavy
enough to carry the current your product will draw. An
undersized cord will cause a drop in line voltage resulting
in loss of power and overheating. The following table
shows the correct size to use depending on cord length
and nameplate ampere rating. If in doubt, use the next
heavier gauge. The smaller the gauge number, the heavier
the cord.
Voltage
Total length of cord in meters (m)
(Volts)
120-127V
0-7
220V
0-15
Rated
Minimal cross-sectional area of the
Ampere
Range
0-6A
1,0
6-10A
1,0
10-12A
1,5
12-16A
2,5
Warning! Before attempting any of the following
operations, make sure the saw blade has stopped, and
the battery is removed or the cord is unplugged. Used saw
blades can be hot.
OPERATING INSTRUCTIONS
Warning! Shock hazard. Under no circumstances
should this product be used near water.
Warning! Risk of lacerations or burns. Do not touch
work piece or accessory immediately after operating the
tool. They can become very hot. Handle carefully. Always
allow accessories and work piece to cool before handling.
Warning! To reduce the risk of injury, turn off and
remove battery from tool or disconnect plug from power
7-15
15-30
15-30
30-60
cord in milimeters (mm
)
2
1,5
1,5
1,5
2,5
1,5
2,5
4,0
Not recommended
30-50
60-100
2,5
4,0
4,0
Publicidad
Tabla de contenido
