Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
source before making any adjustments or removing
or installing attachments or accessories.Remove any
accessory from the attachment before removing or
installing the attachment.
Note: Refer to Power Unit instruction manual before
operating this tool for all safety warnings and details on
installing and removing attachments.
Installing and removing a saw blade (Fig. B)
Warning! To reduce the risk of injury, turn off and
remove battery from the tool or disconnect plug from
power source before making any adjustments or removing
or installing attachments or accessories.
f Access the lever (B1) through the back of the jig saw
attachment.
f Press and hold the lever down with your thumb.
f Insert the saw blade into the blade clamp as shown.
Make sure the teeth are pointing toward the slot
opening in the saw shoe.
f Release the lever.
f To remove the saw blade, press and hold the lever
(B1) down and pull the saw blade from the holder.
Sawing
f To switch the tool on, press the variable speed switch
on the power unit. The tool speed depends on how far
you press the switch.
f To switch the tool off, release the variable speed switch.
f Always use the appropriate type of saw blade for the
workpiece material and type of cut.
f If necessary, drill a hole in the workpiece near the
starting point of the cut so the blade will fit before
starting the cut.
Note: This attachment only operates in the forward
direction, the forward/reverse slider of the Power Unit
should not be able to be switched to reverse.
Making a pocket cut (Fig. C),
it is not necessary to drill a pilot hole:
f Mark the desired starting point.
f Tilt the tool forward and place the rounded front edge
of the saw shoe on the workpiece.
f Switch the tool on and slowly feed the saw blade into
the workpiece at the desired starting point.
Cutting sheet metal
f Use a metal cutting blade. Clamp a piece of plywood
or soft wood to the back of the workpiece and saw
through the combination in order to obtain a clear cut.
f Do not force the saw blade into the workpiece. Note
that cutting sheet metal will normally take more time
than sawing thicker wooden workpieces.
f Spread a thin film of oil along the cutting line before
sawing.
f To cut, place the front of shoe on the material to be
cut. Hold the jig saw shoe firmly against the material
while cutting. Don't force the tool; let the blade cut at
its own speed.
Cutting laminates
f Use a downward cutting blade. Cut thin laminates with
the back surface facing up, as splintering is most likely
to occur on the side of the workpiece facing the saw shoe.
f For clean cuts, clamp a piece of plywood or hardboard
to both sides of the laminate and cut through the
resulting sandwich.
MAINTENANCE
Use only a dry cloth to clean the tool. Never let any liquid
get inside the tool; never immerse any part of the tool into
a liquid.
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper
tool care and regular cleaning. Your charger does not
require any maintenance apart from regular cleaning.
Warning! Before performing any maintenance on the
tool, remove the battery from the tool. Unplug the charger
before cleaning it.
f Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
f Regularly clean the motor housing using a damp
cloth. Do not use any abrasive or solvent-based cleaner.
f Regularly open the chuck and tap it to remove any
dust from the interior.
¡Important! To ensure product SAFETY and
RELIABILITY, repairs, maintenance and adjustment
(other than those listed in this manual) should be performed
by authorized service centers or other qualified organizations,
always using identical replacement parts. Unit contains no
user service able parts inside.
ACCESSORIES
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center.
Warning! The use of any accessory not recommended
for use with this tool could be hazardous.
PROTECTING THE ENVIRONMENT
Separate collection. This product must not be
disposed of with normal household waste.
Should you find one day that your
BLACK+DECKER product needs replacement, or
if it is of no further use to you, do not dispose of it
with household waste. Make this product available
for separate collection.
ENGLISH • 17
Publicidad
Tabla de contenido
