Application; Advice On Application; Procedure For Tens, Ems And Massage Programmes 01-10; Procedure For Tens/Ems Programmes 11-20 (Ind. Prog.) - Beurer EM 80 Instrucciones Para El Uso

7. Application

7.1 Advice on application

• If the device is not used within 3 minutes, it switches off automatically
(automatic switch-off function). When it is switched on again, the LCD
main menu screen appears, with the last used submenu flashing.
• If an admissible key is pressed, there is one short beep. If an inadmissible
key is pressed, there are two short beeps.

7.2 Procedure for TENS, EMS and MASSAGE programmes 01-10

(quick start)
• From the programme charts, select a programme that is
suitable for your purpose.
• Place the electrodes in the area selected and connect these
to the device. The corresponding positioning suggestions
may help you here.
• Press the ON/OFF key in order to switch on the device.
• Press MENU and navigate through the sub-menus (TENS/
EMS/MASSAGE) and confirm your selection with ENTER.
(Fig. 1, example of TENS display)
• Using the UP/DOWN keys, select the programme you want
and confirm with ENTER (Fig. 2, example of display for No. 1
TENS programme).
• Using the UP/DOWN keys, select the total treatment time
and confirm with ENTER (Fig. 3, example of 30-minute treat-
ment duration).
The device is in wait status (Fig. 4).
• Press ON/OFF to start stimulation treatment. Operating
status starts to change and pulse frequency is displayed
alternately with pulse width (Figs. 5 and 6).
• Select the pulse intensity which is the most comfortable for
you by pressing keys CH1±, CH2±, CH3±, CH4±.
The pulse intensity display adapts accordingly.
7.3 Procedure for TENS/EMS programmes 11 to 20
(individual programmes)
Programmes 11 to 20 are preset programmes which you can also individu-
alise.
Here you can set pulse frequency, pulse width as well as the ON and OFF
time of the individual cycles.
• From the programme charts, select a programme that is suitable for your
purpose.
• Place the electrodes in the area selected and connect these to the device.
The corresponding positioning suggestions may help you here.
• Press the ON/OFF key in order to switch on the device.
• Press MENU and navigate through the sub-menus (TENS/
EMS/MASSAGE) and confirm your selection with ENTER.
(Fig. 1, example of TENS display)
Fig. 1
• Using the UP/DOWN keys, select the programme you want
and confirm with ENTER (Fig. 2, example of display for No.
11 TENS programme).
• The number of cycles is displayed (C) (Fig. 3, e.g. 5 cycles).
Fig. 2
To change this, press the UP/DOWN key and confirm by
pressing CYCLE or ENTER.
i You can also change the number of cycles during the
other programming stages by pressing the CYCLE key,
Fig. 3
selecting the required number of cycles with UP/DOWN and
confirming with CYCLE or ENTER.
• To set pulse width, press the key 'μs', choose your setting
with UP/DOWN and confirm by once again pressing the key
Fig. 4
'μs'. Repeat for each cycle (Fig. 4).
• Set pulse frequency by pressing the 'Hz' key. Choose your
setting with UP/DOWN and confirm by once again pressing
'Hz'. Repeat for each cycle (Fig. 5).
Fig. 5
• Press the key
times of the individual cycles. Choose the duration with
UP/DOWN and confirm by once again pressing the key
Repeat for each cycle (Fig. 6).
Fig. 6
i Note: Setting OFF time to '00' ensures that there is no
period of relaxation between the individual cycles.
26
in order to set the respective ON and OFF
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
.
Fig. 6