Electrical Connections - HAMPTON BAY 383-586 Manual De Instrucciones

ASSEMBLY INSTRUCTIONS (AS SHOWN IN DIAGRAM):
This pendant is already assembled and ready for installation to the track section. Proceed to Installing Fixture to Track. Section if you do
not need to adjust the length of the wire. Please follow these instructions if you do need to adjust the length of the wire.
1. On the Adapter, remove the set screw on the side of the top end of the adapter as shown in Figure 1. Unscrew the bushing and
slide it down the wire a few inches. Keep these parts handy for the final installation.
2. Separate the top and bottom portions of the adaptor by unscrewing them from one another. The two parts of the adapter are
joined with screw threads inside the top and bottom section.(See Figure 1)
3. Remove the three (3) wires connected to the three (3) screws inside the top of the adapter. Loosen the knot. Remove the bottom
portion of the adapter, and the bushing from the wire.
4. 4a, Determine the distance from the ceiling where you want to hang the pendant by holding the wire at the ceiling or using a
tape measure. When the desired length is established, MARK THE WIRE WHERE IT MEETS THE CEILING.
4b, make a second mark 3 1/2in. below the first mark. Tie a knot so that it is at the top of the second mark (and between both
markings).
NOTE: If installing more than one pendant and the same height is desired for all pendants make sure the wires on all pendants are
marked at the same length.
CAUTION: Be careful not to cut or damage the insulation on the inside wires when removing the outer insulation.
5. Cut the wire 3in. above the knot.
6. The pendant wire has three (3) smaller wires running inside of it. Remove 3 inches of the outer insulation exposing the three (3)
smaller wires inside.
How to Identify the Wires: The NEUTRAL WIRE is transparent without any marking or simply a white wire, the HOT WIRE is
transparent with font-printed or simply a black wire. The GROUND WIRE is a bare wire or simply a green wire or transparent with a
green/yellow line marking wire.
7. Replace the bushing, bottom portion of the adapter and the knot respectively. Remove a half (1/2) inch of the insulation on all
three (3) of the smaller wires, twist the copper strands and loop each wire to its own screw matching the neutral wire to the
silver screw, the hot wire to the gold screw and the ground wire to the green screw. Tighten screws to secure the wire.
8. Slide the bottom portion of the adapter up to the top and close the adapter by screwing the top and bottom together and replace
set screw.
9. Slide the bushing to the bottom of the adapter and re-attach.
Installing Fixture to Track:
1. IMPORTANT: Determine ground side of track (has indented groove on face and two internal copper bars) and connector (side
of connector with two metal tabs) It can only be installed if grounds are aligned. (See Figure 3)
2. Insert connector into track. Twist ground side of connector towards ground side of track until connector snaps into place and
locks.
Installing fixture to Ceiling: (Refer to Figure 4)
If you want to install the fixture to the ceiling using the direct wire canopy, start with steps 1-3.
NOTE: These fixtures are intended to be used with a 4in. x 2-1/8in. deep metal octagon junction box. The box must be directly supported
by the building structure.
1. Install mounting bracket to existing outlet box with screws.
2. Pull the pendant wire through the bushing and the canopy.
3. To adjust the wire, follow step 4a from above. Tie the knot at the marking and cut the wire 6in. above the knot. Then follow step
6.
4. Wire connections:
A. Make ELECTRICAL CONNECTION as directed below.
B. Carefully tuck connected wires back into the outlet box ensuring that the wire nuts do not come loose.

ELECTRICAL CONNECTIONS

a. Connect the neutral wire from the fixture to the neutral wire of the outlet box.
b. Connect the hot wire from the fixture to the hot wire of the outlet box.
c. Connect the ground wire from the fixture to the ground wire of the outlet box.
Note: Use UL Listed wire connectors suitable for the size, type and number of conductors. No loose strands or loose wires should be
present. Secure wire connectors with UL approved electrical tape.
5. Secure the canopy to the mounting bracket with provided decorative nuts.
Install and replace light bulbs:
CAUTION: Refer to the re-lamping label located near the lamp holder for recommended maximum wattage. Do not exceed
recommended wattage.
1. Be sure the power is off, allow the fixture and bulb to cool, grasp connector and pull down while rotating it counter clockwise.
2. Twist the bulb counter clockwise from the socket to remove it. Insert a new bulb and rotate the bulb clockwise until it is secure.
Remove and replace bulb as needed may be use the bulb re-lamping tool. (Note: Keep re-lamping tool for future use).
3. Restore electric power.
3