Publicidad
To Remove
Step 1: Carefully remove the walker frame and components from
the shipping box.
Step 2: Examine all parts for damage from shipping. If any parts are
missing or damaged, please call 1-800-557-6682 and prompt
Customer Service. DO NOT use walker until all parts are
received.
Components
Walker Frame with Bag and Seat, Backrest (see image 1)
(2) Front Wheels (see image 2)
(2) Rear Wheels with Cable Handle and Hand Brake (see image 3)
(6) Leg and Handle Adjustment Screws (see image 4)
Lea el Manual de Instrucciones antes de utilizar cualquier andadera de Nova.
Para Sacar
Primer paso: Cuidadosamente saque el marco de la andadera y todas sus partes de la caja.
Segundo paso: Revise que las partes no estén dañadas por causa de ser enviadas. Si falta o está dañada alguna parte,
por favor llame al 1-800-557-6682 para el Servicio de reclamaciones. No utilice la andadera hasta que
reciba todas las partes.
Partes
Marco de andadera con la bolsa, un asiento, y un respaldo (vea imagen 1)
(2) Ruedas delanteras (vea imagen 2)
(2) Ruedas traseras con cable para el freno de mano (vea imagen 3)
(6) Tornillos para ajustar las piernas y las agarraderas (vea imagen 4)
To Unfold
Step 1: Unfold the walker by pulling the front and rear frame apart and place on a flat surface. Lift the seat and push
downward on the folding support piece so the side folding hinges are fully extended. (see image 5)
Step 2: Insert the backrest into the plastic backrest hinges. Press down on the push buttons and slide the backrest
completely into the hinge until the buttons engage into the hinge holes. (see image 6) Pull on the backrest to
make sure it is secure.
Step 3: Turn the walker so that it rests on the rear of the frame. (see image 7)
Step 4: Insert the front wheels into the frame for your desired seat height.
(See recommended seat height below)
Recommended Seat Height
The user's feet should be flat on the ground when they are properly seated on the walker. We recommend the lower
seat height to fit most individuals from 4'-10" – 5'5" and the higher seat height for individuals from 5'5"- 6'1".
For Heights 5'5" - 6'1" (upper push button)
Push down on the top button and slide the stem into the frame. You will need to press down on the second button to
allow the top button to insert into the hole on the frame. (see image 8)
For Heights 4'10" - 5'5" (lower push button)
Align the button just off center from the hole in the frame and slide the stem into the frame. Press down again on the
lower button and continue to slide the stem into the frame while aligning the lower button with the hole on the frame
until the lower button is inserted into the hole. (see image 9) Be sure that both wheels are set at the same height
and pull on the legs to make sure they are secure.
Step 5: Turn walker over so that it rests on the front of the frame. (see image 10)
Step 6: Insert the wheel leg marked (L) into the left rear frame so that the wheel is on the outside of the frame and the
push buttons are lined up with the hold in the frame. (see image 11)
Step 7: Insert the wheel leg marked (R) into the right rear frame so that the wheel is on the outside of the frame and the
push buttons are lined up with the hole in the frame. (see image 12)
(See recommended seat height above)
Step 8: Turn the walker over so that it is resting on the wheels. Be sure that all the four wheels are flat and that the seat
is level. (see image 13)
Step 9: Insert the handles into the frame being sure that the cables are on the outside of the frame. (see image 14)
Step 10: Insert the four leg attachment screws into the holes located on the outside of the frame. Hand tighten until
the screw is secure and the plastic knob is flush with the frame. Adjustment handle should be tight and not
move from side to side. Be sure all four screw legs screws are secure before using the walker. (see image 15)
Assembly Instructions
Instrucciones de ensamblaje
1
3
2
4
Publicidad
