Maintenance; Disposing Of The Packaging; Troubleshooting - Surtek BC603 Manual De Usuario Y Garantía

AFTER THE CONNECTION WAS MADE, CARE-
FULLY VERIFY THAT THE VOLTAGE AT THE WIRES
THAT WILL BE CONNECTED TO YOUR MOTOR
PUMP IS THE VOLTAGE NEEDED FOR OPERA-
TION. IF VOLTAGE IS DIFFERENT, CORRECT IT.
AFTER THE CONNECTIONS ARE COMPLETED
AND BEFORE CONNECTING TO THE POWER
LINE, MAKE SURE THAT THIS SWITCH IS OPEN
AND ALL THE CABLES AND UNIONS ARE DULY
ISOLATED AND PROTECTED.
ALWAYS DO THE CONNECTIONS WITHOUT
POWER IN THE LINE.
BEFORE STARTING YOUR MOTOR
Drain (fill up with wa-
ter) your pump and
verify that there are
no air entrance or
leaks in the pipes or
in the foot valve.
Wait some minutes
and make sure that
the level has not
dropped.
NEVER OPERATE THE PUMP WHEN IT IS EMP-
TY. IF THIS HAPPENS ACCIDENTALLY TURN THE
PUMP OFF, WAIT FOR IT TO COOL AND THEN
TURN IT ON USING CLEAN WATER.

MAINTENANCE

- The pump does not require maintenance as
long as the following precautions are taken:
when there is a risk of freezing, empty the pump
by removing the suction tube, ensuring that the
pump is primed when it is started again, check
that the foot valve is cleaned at regular inter-
vals, if the pump is to remain inactive for an
extended period of time it is advisable empty it
completely, rinse it with clean water and store it
in a dry place. if the arrow does not turn freely,
release it using a screwdriver, there is a hole in
the back of the pump that gives access to the
arrow, turn it with the help of the screwdriver,
if this does not solve the problem remove the
pump body, by loosening the corresponding
mounting screws and clean it perfectly to re-
move any incrustation.
NEVER CARRY OUT WORK ON THE PUMP
WITHOUT FIRST DISCONNECTING IT FROM
THE MAINS.- TO IDENTIFY WHERE THE WATER
LEAKS ARE, DRY THE MOTOR PUMP AND PIPING
AND FILL IT UP AGAIN WITH WATER.
14
- Below you will find a box with the problems
that may arise.
- If you find any failure in your motor pump,
even out of the Guarantee term or if you need-
ed to repair the product by yourself, we remind
you that we have authorized service shops.
CONSIDERATIONS TO INSTALL THE WATER TANK
It is recommended to install a foot valve with
a diameter wider than the pump´s suction to
avoid losses due to friction.
DISPOSING OF THE APPLIANCE
This product must not be disposed of in house-
hold rubbish. You must dispose of such old elec-
trical and electronic equipment separately.
- Please check with your local authority about
the possibilities for correct disposal.
Through separate disposal you send old equip-
ment for recycling or for other forms of re-use.
You will thus help to avoid in some cases that
damaging material gets into the environment.

DISPOSING OF THE PACKAGING

The packaging consists of cardboard and corre-
spondingly marked plastics that can be recycled.
- Make these materials available for recycling.

TROUBLESHOOTING

DANGER: Improperly conducted repairs may
prevent your appliance from working safely.
Such re airs will endanger you and your sur-
roundings.
Minor faults are often sufficient to cause a
malfunction. In most cases, you will be able to
correct these faults easily yourself. Please start
by referring to the following list before contact-
ing our technical support. This will help you save
much effort and possibly expense.
PROBLEMS THAT MAY ARISE
Possible failure. Corrective action
THE PUPM SPILLS WATER
Loose or badly sealed pipes. Identify the place of
the leak and use some type of sealant (SURTEK
threads sealer tape, Cement, Pola, etc.) When
doing the connections again.
Damaged coupling seal and/or loose screws.
Replace the damaged parts and securely tighten
the screws, being careful not to strip them.
Defective mechanical seal. Replace the dam-
aged parts and assembly again your motor
pump making sure no part is loose.
®