Disassemble / Reassemble And Cleaning Of Rear Internals; A Jammed Paintball - Spyder ELECTRA Manual Del Usuario

DISASSEMBLE / REASSEMBLE AND CLEANING OF REAR INTERNALS

REC028
REC029
Part Names and Numbers described in this section:
Top Cocking Knob (#STK008)
Delrin Bolt (#VBT008)
Striker Bolt (#STB002)
Striker Plug (#STP028/STP029)
QUICK CLEAN DISASSEMBLY
Lift upward on the Top Cocking Knob to disconnect the Delrin Bolt from the Striker Bolt. This will allow the Delrin Bolt to slide
out from the rear of the Receiver. HELPFUL TIP: Removing the Delrin Bolt from the Receiver will allow easy access
to clean with a squeegee. NOTE: Make sure the hole on the Striker Bolt is facing upright when looking thru the
Receiver. This will allow the Top Cocking Pin to correctly fasten with the Striker Bolt.
IMPORTANT: The air passage hole located in the middle of the Delrin Bolt should always be facing downward when
reinstalling. If the Delrin Bolt is not installed correctly, paintballs will not exit out of the barrel normally.
DISASSEMBLE OF REAR INTERNALS
STEP 1 Lift upward on the Top Cocking Knob to disconnect the Delrin Bolt from the Striker Bolt. This will allow the
Delrin Bolt to slide out from the rear of the Receiver.
STEP 2 Using an adjustable wrench turn the Striker Plug counter clockwise located at the rear of the Receiver. This
will allow all internal parts such as the Velocity Adjuster & Spring Guide, Striker Spring, Striker Buffer and Striker
Bolt to slide from the rear of the Receiver.
NOTE: Remove the Striker Plug only with the marker in the un-cocked position this will prevent the internals from
springing out because the Striker Spring is compressed.
before removing this will prevent the markers internals from springing out.
STEP 3 Remove items in order; Striker Plug w/Velocity Adjuster, Striker Spring and Striker Buffer.
STEP 4 Slide the Striker Bolt out of the rear of the Receiver.
would be wise to clean any dirt or paint from the inside of the Receiver with a squeegee and wipe the Delrin Bolt
clean with a rag or paper towel. Apply some paintball gun oil on Striker O-ring periodically.
IMPORTANT: It is not necessary to disassemble the rear internals for basic maintenance unless the Striker O-ring
needs to be replaced.
11
VBT008
STK008
STF001
STP028
STP029
SPR004
STB002
Striker Spring (#SPR004)
Striker Buffer (#STF001)
Receiver (#REC028/REC029)
HELPFUL TIP: Placing your finger behind the Striker Plug
HELPFUL TIP: When the internals are removed it
REASSEMBLY REAR INTERNALS
CONNECTED
STEP 1 Reinsert the Striker Bolt with Striker O-ring facing toward the front of the marker with the flat spot of the
Striker Bolt facing down. NOTE: Having the Power Switch ON will ease reentry of the Striker Bolt. Apply thumb
pressure behind the Bolt and at the same time pull on the Trigger. Repeat this process until the Bolt is fully inserted.
NOTE: The hole on the Striker Bolt should be facing upright when looking thru the Receiver.
above display the Delrin Bolt "connected" to and "disconnected" from the Striker Bolt.
STEP 2 Insert the Striker Buffer flush with the receiver and place the Striker Spring thru the Striker Buffer.
STEP 3 Tighten firmly the Striker Plug w / Velocity Adjuster & Spring Guide to the rear of the Receiver.
STEP 4 Insert the Delrin Bolt thru the rear of the Receiver with the Top Cocking Pin. Press downward on the Top
Cocking Pin to gain entry with the Striker Bolt. NOTE:
Pin will not fasten correctly.
WARNING: Before / after use of the marker, make sure to fasten all screws. Screws may become loose due to
vibration. Loose screws can be dangerous and cause injury.
To assure that the marker is assembled properly, follow the schematic drawing or position parts in order during
disassembly. Parts assembled backwards or improper parts installed will / can cause the marker to malfunction.
A JAMMED PAINTBALL IN THE BREACH
In the event of a paintball break and the Delrin Bolt jams, follow these steps to help un-jam the marker. The markers
breach is located where the barrel starts to thread in the receiver and underneath the markers feed neck. Before
attempting to un-jam the Delrin Bolt you should always have your Goggles or Safety Glasses on. Make sure the
marker is in the SAFE / OFF position before attempting to un-jam the Delrin Bolt. Remove the CO2 / Compressed
Air Tank before attempting to un-jam the marker. Remove all paintballs and the loader from the feed neck. Have the
barrel removed from the receiver to allow the paintball (s) to exit. With enough force on the Cocking Knob, pull back
to release the Delrin Bolt from the jammed position. Another method is to use a "Straight Shot Squeegee" or the end
of a wood dowel rod; push against the face of the Delrin Bolt with enough force to release the jammed Bolt. Always
clean the paint from the breach and barrel to enhance the performance of your marker.
IMPORTANT: Never look down the barrel of the marker when loaded or unloaded. Remove the attached CO2 /
Compressed Air Tank before attempting to un-jam the Delrin Bolt.
NOTE: Never use a metal rod or screwdriver as a tool to push on the Delrin Bolt, anything metal will scratch and
damage the inside of the marker.
English
DISCONNECTED
NOTE: The images
If the Striker Bolt hole is not aligned upright, the Top Cocking
12