Anti Chop Eyes / Changing Ball Stoppers; Cup Seal Removal - Spyder ELECTRA Manual Del Usuario

ANTI CHOP EYES
BLS 011
BLS012
BLS014
BLS015
SCR002
Part Names and Numbers described in this section:
Eye Panel (#BLS011/BLS012/ BLS014/BLS015)
Ball Stopper (#BLS003)
Eye Panel Screw (#SCR002)
Eye Wire Harness (#WRH008)
ANTI CHOP EYES
The Anti Chop Eyes help prevent the chopping of paint by not allowing the marker to fire until a paintball is properly
chambered in the breach. The Eyes transmit a beam across the inside of the breech. The circuit board is preset from
the factory and does not need to be adjusted or altered. (If the Eyes are ON and do not see each other when firing
your marker, you will have to clean the Eyes.) NOTE:
paintballs but do not completely eliminate it from happening, keep the Anti Chop Eyes clean for best and reliable
performance.
CLEANING THE ANTI CHOP EYES
Using a squeegee or swab thru the breech should clean the Eyes enough for the Eyes to detect each other. Another
way is to use an aerosol can of air thru the breech to remove any paint or dirt. To thoroughly clean the Eyes using
the supplied Allen wrench remove both Eye Panel Screws and Eye Panels . Once the Eye Panel Screws & Eye
Panels are removed, proceed with a soft pinch to remove the Eye Wire Harness from the receiver. Use a cloth or
paper towel to remove any paint or dirt that is blocking the Eyes.
IMPORTANT: Cleaning the Eyes often will help reduce dirt, paint or oil residue that blocks the Eyes
NOTE: Never attempt to rush the cleaning process or you can pinch the wires and cause the marker to malfunction
with the Eye Mode ON. Take precaution not to over tighten the Eye Panel Screws or this can lead to stripping the
head. NOTE: When the Eye Panels are removed the Ball Stopper(s) may be attached to the Eye Panels and can
cause them to fall out. HELPFUL TIP: Please note how the parts are removed for easy reassembly.
IMPORTANT: Before removing both Eye Panels use a needle or dental pick through the hole of the Eye Panel to
remove any dirt that may have built up and prevent the Allen wrench from loosening the screw. It's possible if the
dirt is not removed you can strip the Eye Panel Screw.
NOTE: Maintenance cleaning of the Anti Chop Eyes should only be done if a paintball break in the breach has
occurred and affected the detection of the paintballs. Removing the Delrin Bolt and pushing a swab type squeegee
through the breach may be adequate in cleaning the Anti Chop Eyes.
CHANGING THE BALL STOPPERS
Experiencing paint rolling through the barrel can be related to small diameter paintballs or the loss of a Ball
Stopper(s) . When removing Eye Panel Screws and Eye Panels the Ball Stopper(s) will be accessible for cleaning or
replacement.
HELPFUL TIP: Please note how the parts are removed for easy reassembly.
IMPORTANT: Before removing both Eye Panels use a needle or dental pick thru the hole of the Eye Panel to remove
any dirt that can build up and block the Allen screw from loosing. It's possible if the dirt is not removed you can stripe
the Eye Panel Screw.
NOTE: Take precaution not to over tighten the Eye Panel Screws or this can strip the head.
not required for the Ball Stoppers unless they have completely worn out or is unable to keep a paintball from rolling
out the breach of the marker when the marker is pointed down.
13
BLS003
WRH008
The Anti Chop Eyes system reduces the likelihood of chopping
NOTE: Maintenance is

CUP SEAL REMOVAL

ITP012
LPC028
ITP017
LPC029
ITP011
SPR013
VRT028
VRT029
REG028
REG029
Part Names and Numbers described in this section:
Regulator (#REG028/REG029)
Cup Seal Guide (#ITP011)
Cup Seal (#ITP012)
Valve Pin (#ITP017)
M5x20 Vertical Washer (#ITP019)
STEP BY STEP CUP SEAL ACCESS
Access of the cup seal for service or replacement requires the removal of the Front Plug and Vertical CA Adapter.
STEP 1 Unscrew the Regulator from the Vertical CA Adapter.
STEP 2 Remove the Vertical CA Adapter by unscrewing the Vertical CA Adapter Mounting Screw, be sure to keep a
finger over the Front Plug to prevent it from springing out.
NOTE: The Front Plug and Vertical CA Adapter are both held in place by the Vertical CA Adapter Mounting Screw.
STEP 3 Pull the Front Plug out and it should come out with the Valve Spring, Cup Seal Guide, Cup Seal and Valve
Pin all together.
STEP 4 Unscrew the Cup Seal from the Valve Pin and replace with the spare provided with your spare parts kit.
STEP 5 Follow the previous steps in reverse to re-install all components properly. Make sure the Front Plug screw
hole is lined up with the vertical adapter screw hole.
IMPORTANT: Always make sure all air sources have been removed from your marker and any residual air has been
vented out completely before servicing your marker.
NOTE: Service or replacement of the Cup Seal should only be done if a leak is present and can be heard from the
breach after the removal of the Delrin Bolt.
ITP019
SCR027
Front Plug (#LPC028/LPC029)
Valve Spring (#SPR013)
Vertical Adapter (#VRT028/VRT029)
Vertical Adapter Mounting Screw (#SCR027)
English
14