Husky DPFR2190 Manual De Instrucciones página 4

Respect the tool as a working implement.
Never engage in horseplay.
Never pull the trigger unless nose is directed
toward the work.
Keep others a safe distance from the tool
while tool is in operation as accidental
actuation may occur, possibly causing injury.
AIR SUPPLY AND CONNECTIONS
● The connector on the tool must not hold
pressure when air supply is disconnected.
an incorrect fitting is used, the tool can remain
charged with air after disconnecting and thus will
be able to drive a fastener even after the air line
is disconnected, possibly causing injury.
● Do not use any type of reactive gases,
including, but not limited to, oxygen and
combustible gases, as a power source.
filtered, lubricated, regulated compressed air
only. Use of a reactive gas instead of
compressed air may cause the tool to explode
which will cause death or serious personal injury.
● Use only a pressure-regulated compressed
air source to limit the air pressure supplied to
the tool. The regulated pressure must not
exceed 100psi. If the regulator fails, the pressure
delivered to the tool must not exceed 200psi.
●
Always disconnect air source:
◆Before unloading or making adjustments.
◆When maintaining the tool.
◆When clearing a jam.
◆ When touching the safety yoke.
◆When tool is not in use.
◆When moving to a different work area.
Such precautionary measures reduce the risk
of injury to persons.
LOADING TOOL
●
Do not load the tool with fasteners when any
one of the operating controls is activated.
● Never place a hand or any part of body in
fastener discharge area of tool.
● Never point tool at anyone.
● Do not pull the trigger or depress the
workpiece contact as accidental actuation
may occur, possibly causing injury.
06
WARNING:
!
The warnings and precautions discussed
above cannot cover all possible
conditions and situations that may occur.
It must be understood by the user that
common sense and caution are factors
which cannot be built into this product,
but must be supplied by the user.
If
UNPACKING
● This tool has been shipped completely
assembled.
●
Carefully remove the tool and any
accessories from the box.
● Inspect the tool carefully to make sure no
breakage or damage occurred during
Use
shipping.
● Do not discard the packing material until you
have carefully inspected and satisfactorily
operated the tool.
● If any parts are damaged or missing, please
call 1-866-676-8468 .
WARNING:
!
If any parts are missing do not operate
this tool until the missing parts are
replaced. Failure to do so could result in
possible serious personal injury.
WARNING:
!
Do not attempt to modify this tool or
create accessories not recommended for
use with this tool. Any such alteration or
modification is misuse and could result in
hazardous condition leading to possible
serious personal injury.
FEATURES
SPECIFICATIONS
REQUIRES: 7.00 SCFM with 100
fasteners per minute @ 80 psi
AIR INLET: 1/4 inch NPT
MAGAZINE CAPACITY:
55 fasteners, 10-12 gauge
WEIGHT: 7,48 lbs
MAXIMUM PRESSURE: 115 psi
PRESSURE RANGE: 70 psi 115 psi –
PIN SIZE RANGE: 2 inch to 3-1/2 inch
Compatible with all brands of plastic collated
21° full head framing nails.
FEATURES
ONE PIECE DRIVER BLADE
For increased durability.
COMFORT-GRIP HANDLE
For increased comfort and control.
MAGNESIUM BODY
Lightweight tool is great for extended use.
DUAL-MODE TRIGGER
Easily allows for Single or Sequential Firing.
ADJUSTABLE DEPTH
Depth is easily adjustable for various
applications.
ANTI-DRY FIRING DESIGN
Reduces damage on internal components.
NON-MARRING SAFETY CONTACT
Eliminates damage to working surface.
OPERATION
LOADING FASTENERS
⒈ Connect the tool to the air source.
f
⒉ Insert strip of fasteners rom the rear of
magazine(A). Be sure the fasteners are pointed
downward .(See figure 1 & figure 2)
⒊ This tool uses a spring loaded bypass lever in
order to load and upload the nails. Once the nails
are properly inserted, pull the pusher(B)
completely back, pressing against the bypass
lever of the pusher.(See figure 3)
4 . Once the pusher hits the back of magazine,
allow the pusher to slide forward and engage the
nails, pushing them to the nose of the tool.
(See figure 4)
Figure 1
Rear of magazine(A)
Head of nail
INSERT NAIL STRIP
Figure 2
MAXIMUM
LOAD
Nail Hold Back Spring
07