Matco Tools MT1745 Instrucciones De Operación página 3

AIR suPPly
Tools of this class operate on a wide range of air pressures . It is
recommended that air pressure of these tools measures 90 PSI
at the tool while running free . Higher pressure and unclean air will
shorten tool life because of faster wear and may create a
hazardous condition .
Water in the air line will cause damage to the tool . Drain the
air tank daily . Clean the air inlet filter screen on at least a weekly
schedule . The recommended hook-up procedure can be viewed
in Figure 1 .
The air inlet (Figure 2), used for connecting air supply, has standard 1/4" NPT
American Thread .
Line pressure should be increased to compensate for unusually
long air hoses (over 25 feet) . Minimum hose diameter should be 3/8" I .D . and
fittings should have the same inside dimensions .
Nipple
WARRANTy
Matco warrants its air tools for a period of 1 year to the consumer . We will
repair any MT Series air tool covered under this warranty which proves to
be defective in material or workmanship during the warranty period . In order
to have your tool repaired, return the tool to either of the Matco Authorized
Warranty Centers listed to the right, freight prepaid . Please include a copy of
your proof of purchase and a brief description of the problem . The tool will
be inspected and if any part or parts are found to be defective in material
or workmanship, the tool will be repaired free of charge and returned to you
freight prepaid .
This warranty gives you specific rights . You may also have other rights which
vary from state to state .
The foregoing obligation is Matco's sole liability under this or any implied
warranty and under no circumstances shall Matco be liable for any incidental
or consequential damages .
Note: Some states do not allow the exclusion or limitation of
incidental or consequential damages so the above limitation or exclusion may
not apply to you .
MT1745
MT1745 Mini Composite 1/4" Impact Wrench
fEATuREs
• Ideal for fastening in hard to reach areas where most tools can not go such as under
the dash work and small engine repair .
• Excellent power to weight ratio gets the job done with less fatigue.
• Durable composite housing makes this tool lightweight, comfortable, and chemical
resistant .
• Dust free forward/reverse lever.
• Variable speed throttle for maximum control.
TROuBlEshOOTINg
Other factors outside the tool may cause loss of power or erratic
action . Reduced compressor output, excessive drain on the air line,
moisture or restrictions in air pipes or the use of hose connections
of improper size or poor conditions may reduce air supply . If
outside conditions are in order, and the tool still performs erratically, disconnect
tool from hose and take tool to your nearest Matco authorized service center .
luBRIcATION & MAINTENANcE
Lubricate the tool daily with a good grade of air tool oil . If no
air line oiler is used, run a 1/2 ounce of oil through the tool . The oil can
be squirted into the tool air inlet, Figure 2, or into the hose at the nearest
connection to the air supply, then run the tool . A rust inhibitive oil is acceptable
for air tools .
AIR
INLET
fIg. 1
MATcO AIR cOMMANd
Tool Repair SV
1330 Commerce Dr .
Stow, OH 44224
(800) 433-7098
dIscOuNT TOOl REPAIR
3433 Losee Rd . #1
North Las Vegas, NV 89030
(702) 657-6570
PNEuTOOl PARTs & sERVIcEs cO., lTd
TOOl REPAIR
33 Hass Road
Toronto
ON M9W 3A1 Canada
(416) 748-1200
(888)748-1201 (Toll-Free in Canada)
3
TRIGGER
fIg. 2
rev. 04/21/08