Hozelock PURE 7L Manual De Instrucciones página 7

- If you spray until there is just air in the jet: eliminate residual pressure
remaining in the apparatus by operating the safety valve or by spraying
until there is no more pressure (Fig. 16). The residual volume of liquid is
less than 250 ml.
- Before storing and before any other use with another treatment agent,
perform a rinsing operation, i.e. put 1 litre of water into the reservoir for
dilution (Fig. 17), mix thoroughly and operate the apparatus to rinse all of
the sprayer's components. This rinsing operation must be carried out
without removing any of the accessories used during the treatment. This
rinsing mixture must not be emptied into a sewer but must be sprayed
outside on the land that has already been treated.
- Repeat the operation several times before overwintering.
- If there is still some unused treatment product left, eliminate any residual
pressure remaining in the apparatus by operating the safety valve (Fig.
16). Recover any possible excess of product and rinse the sprayer again
as indicated above.
- Before using again, even if it is used again immediately, with a different
spraying solution, repeat the rinsing operation 3 consecutive times.
- Before using again, even if it is used again immediately, with the same
treatment product or a different one, check that the sprayer works properly
(especially the valve). treated in 1 min x nozzle output = 100 m²/20 m²/min
x 0.66L/min = 3.3 litres; i.e. 3.3-0.6 = 2.7 litres of water and 0.6 litres of
treatment product.
- This calculation is only given as an indication. During actual use, take into
account the information provided by the manufacturer of the treatment
product and the data on the nozzle output table.
MAINTENANCE
- Periodically, on re-use after overwintering and several times per season,
grease all the joints (with silicone grease for sprayers) and check that the
sprayer is working properly (especially the valve).
- Clean the nozzle and the nozzle holder (Fig. 20)
- Clean the lance filter (Fig. 21)
- Remove the pump (Fig.22)
- Grease or replace the valve and the seals (Fig.22)
FAULTS / SOLUTIONS
Problems
Make sure that all the connectors are fully tightened
Make sure that all the seals are lubricated and clean
Little or no
and are not damaged or worn. Replace them if
spraying
necessary (contact the customer service department).
Clean the nozzle and the filters
The spraying is
Clean the nozzle
not straight
Make sure that all the connectors are fully tightened
Make sure that all the seals are lubricated and clean
Leaks
and are not damaged or worn. Replace them if
necessary (contact the customer service department).
Safety valve DANGER: Do not pressurise the appliance Contact
defective the customer service department
Solutions
WARRANTIES
Extended cover
Guarantee period and scope:
- We guarantee our products for a period specified in the specific manual
attached to the product or on the product from their date of purchase
(Compulsory Cover extended to 2 years + Extension of our Contractual
Warranty).
- On failure to present proof of the date of purchase of the products, the
Warranty is effective from the date of manufacture of the product (stated
underneath the product).
Warranty disclaimer:
This Warranty does not cover:
- Normal wear parts: seals, valves, handle, nozzle, piping, carrying straps,
rod and lever,
- Modified products,
- Products whose use contradicts the technical recommendations
stipulated in the User Manuals accompanying the product,
- Products used improperly,
- Products not undergoing regular maintenance,
- Product deteriorations (impacts, falls, crushing, etc.) originating from
negligence, improper maintenance, improper use or abnormal use of the
product,
- The replacement of a component after losing a component of the sprayer.
Warranty activation:
- We ask that you keep proof of purchase (invoice or legible till receipt), as
this will be requested on activation of the Contractual Warranty.
- A product under warranty that has been repaired or replaced, remains
guaranteed for the remaining duration and under the original conditions of
the Contractual Warranty granted at the time of purchase. All returned
products become the property of HOZELOCK-EXEL when replaced by a
new product.
Legal Warranty
- The Mandatory Cover, the conditions of which are recalled hereinabove, does
not replace the Legal Warranty.
EC
DECLARATION DE CONFORMITE CE
EC DECLARATION OF CONFORMITY
I the undersigned Jérôme BOULMIER – Quality Manager - certify with this
declaration that the product
Type: Pressure sprayer
Brand : HOZELOCK
Model: Hozelock PURE 7L Sprayer
Ref : 4550 0000 / 4550 3920
Has been developed, designed and manufactured according to all the
relevant provisions in the "Machine Safety Directive" 2006/42/EC
Signed in Villefranche,
18/08/2016